All questions — page 120
Browse by Problem
-
the pellets won't feed into the fire pot, it just beeps and shuts down after a few minutes.
A pellet feed jam. Moisture-swollen pellets or fines (sawdust) are clogging the auger tube. Turn off and unplug the grill. Empty the pellet hopper completely. …
-
i can't get the app to connect to my grill, it just spins and fails every time.
The connection failure on the Ninja Woodfire Outdoor Grill OG701 typically stems from a handshake timeout between the grill's internal Wi-Fi module and your mo…
-
the fan on my ninja woodfire is crazy loud and sounds like it's grinding, is that normal?
No. The convection fan should have a steady hum. A grinding noise means the fan blade is hitting something or the bearing is failing. Turn off and unplug the g…
-
my woodfire grill just flashes 'err' on the screen and won't start heating, what does that mean?
The ERR code is a generic fault. On the OG701, it usually means the main control board detected a problem with a critical component at startup. Unplug the gril…
-
just assembled my 850 and the control panel is blank, no lights, nothing. checked the outlet, it's good.
The controller is not receiving power after assembly. The most likely cause is an unplugged internal wiring harness or a blown fuse on the control board. Check…
-
how do you clean the grease tray on this thing? it's welded in there and the drip cups don't catch half of it.
Grease is bypassing the slide-out grease tray and dripping into the base of the grill. This is a design flaw in the stock setup. The factory grease management …
-
the auger on my pellet grill is making a loud clicking sound but it's not turning. hopper is full.
The auger motor is jammed. The clicking is the motor's internal clutch or gear train slipping. A rock, clump of degraded pellets, or foreign object is lodged i…
-
my temperature is all over the place, set it to 250 and it swings from 180 to 350. how do i fix this?
The grill is experiencing extreme temperature instability. Primary cause is a dirty or faulty RTD temperature probe. Secondary cause is poor pellet quality or …
-
i can't get the app to connect to my navigator grill, it just spins forever. bluetooth is on.
The Pit Boss Connect app is failing to pair with the grill's Bluetooth module. Common causes are incorrect app procedure, phone permissions, or a weak signal d…
-
the fan on my pit boss is making a loud grinding noise, it's not the normal hum. sounds bad.
The convection fan motor bearings are failing or fan blades are contacting the housing. Debris ingress or heat stress is the typical cause. The fan is located …
-
why does my 850 keep shutting off randomly in the middle of a cook? it just goes dead.
The grill is experiencing a power interruption. The most common cause is the auger jamming, which triggers a safety shutdown. A close second is a faulty connec…
-
my navigator 850 just shows er1 on the screen and won't light up, what is that?
The controller is displaying an ER1 error code. This is a low-temperature fault. The firepot failed to ignite or the grill did not reach a safe temperature wit…
-
after the latest firmware update, my grill's fan sounds different and way louder. did it break itself?
It didn't break, it's likely behaving as programmed. Weber has released firmware updates for the EX4 that intentionally changed the fan speed profiles, often m…
-
the startup cycle takes forever and sometimes fails with an 'igniter' message. do i need a new igniter?
Probably, but not definitely. A slow or failed ignition is often due to poor airflow over the hot rod igniter, starving it of oxygen. This is frequently caused…
-
grease is pouring out from under the grill and down the legs, not into the cup. what did i do wrong?
You didn't do anything wrong; this is the infamous 'grease waterfall' issue, especially on early cooks or with fatty meats. The grease is missing the collectio…
-
my smokefire just shut down in the middle of cooking and now it won't turn back on, no lights, nothing.
A total, sudden power loss like that points directly to the safety thermal fuse. It's a one-time fuse on the control board that blows if things get too hot ins…
-
the temperature on my ex4 is swinging wildly, like +/- 50 degrees from where i set it. is it broken?
Big temp swings are usually a symptom, not the root cause. The most common culprit is a dirty or faulty temperature probe inside the cooking chamber, which mak…
-
i can't get my grill to connect to the app, it just spins forever. my phone's bluetooth and wifi are on.
The setup process for the Weber Connect app is notoriously finicky. The most likely cause is that your phone is trying to connect to your 5GHz home WiFi networ…
-
why does my smokefire make a loud, repetitive clicking noise from the hopper when i'm not even using it?
Yeah, this one's common and freaks people out. That's the auger doing a periodic reverse cycle. It's a programmed feature, not a bug, to prevent a 'heat bridge…
-
my smokefire ex4 just shows 'err' on the screen and won't start up, what's going on?
That's the controller's catch-all error state. It usually means the auger motor or the fan motor is failing to initialize on startup, which is a pretty common …
-
just assembled my new ironwood 650 and it won't power on at all, no lights, nothing
This is almost always an assembly error—the main power cable isn't fully seated or a safety interlock isn't engaged. Check the main power connection at the bac…
-
pellet hopper on my ironwood says it's empty on the app when it's clearly full
The pellet sensor (a small paddle wheel in the hopper) is stuck or its mechanism is bound by pellet dust or a stray pellet. Empty the hopper. Locate the sensor…
-
the fan on my ironwood runs non-stop, even hours after shutdown, is that normal?
No, it's not. The fan should shut off after the cool-down cycle (about 15-20 minutes). Continuous running indicates a controller software glitch or a stuck rel…
-
how do i stop insane amounts of grease from pooling in the bottom of my ironwood 650?
The grease management system is overwhelmed or misaligned. The drip tray channel isn't directing grease to the bucket effectively. Check the slope. The grill m…
-
my ironwood won't get above 300 degrees, just sits at like 250 even when set to 400
Insufficient airflow or a dirty temperature probe causing the controller to misread and underfeed pellets. Clean the RTD probe. Let the grill cool, unplug it, …
-
there's a loud clicking or grinding noise coming from the bottom of my ironwood during startup
That's the sound of the auger motor struggling, usually because pellets are jammed in the auger tube or hopper. Immediately turn the grill off and unplug it. E…
-
traeger app says my ironwood is offline but it's right next to the router, won't connect
The grill's Wi-Fi module has likely lost its pairing or is struggling with a 2.4GHz network conflict. It only works on 2.4GHz networks. Re-pair from scratch. O…
-
my ironwood 650 just shows 'err' on the screen and won't start, what's wrong?
The controller is detecting a fault in the startup sequence, most commonly a failed firepot ignition or a problem with the RTD temperature probe. Start with th…
-
there’s a burning smell coming from my lasko fan when it runs, not just dust.
A burning smell indicates something is overheating. The most common causes are a failing motor bearing (causing friction) or an electrical component on the con…
-
my fan’s timer doesn’t shut it off, it just runs all night no matter what i set.
The timer function on the control board is malfunctioning. This is an electronic timing circuit failure, not a mechanical one. The is to replace the main contr…
-
the remote for my lasko 2511 stopped working, i changed the batteries but no luck.
Either the remote’s infrared LED has failed (common) or the infrared receiver sensor on the fan’s control panel is blocked or dead. First, test if it’s the rem…
-
the fan wobbles a lot on its base even on a flat floor, feels really unstable.
The fan isn’t properly seated into its base, or the locking mechanism in the base isn’t engaged. It’s a simple assembly issue. Let’s reseat it. 1) Unplug the f…
-
my tower fan turns on but only works on the high setting, the low and medium buttons do nothing.
The fan motor is getting power, but the control for the lower speeds has failed. This is usually a problem with the circuit board behind the control panel, spe…
-
how do you clean the dust out of a lasko tower fan? the grill looks impossible to open.
Dust buildup on the internal blower wheel is causing reduced airflow and noise. The grille isn’t meant to be fully removed for routine cleaning, but you can ge…
-
why does my lasko 2511 fan make a loud clicking or grinding noise when it oscillates?
That grinding is almost certainly the plastic oscillation gear wearing out or stripping. It’s a weak point in the design after a lot of use. You’ll need to rep…
-
my lasko tower fan just stopped working, no lights, no response to any button, what gives?
You’ve got a complete power failure. The most likely culprit is that the fan’s internal thermal fuse, a small safety device, has blown, which is a common failu…
-
the airflow from my tp07 feels really weak even on max speed, i just put in a new filter
The new filter's packaging plastic or sealing tape was not fully removed before installation, blocking airflow. Power off and unplug the machine. Remove the fi…
-
dyson tp07 won't turn on at all, no lights, no response, but it's plugged in
The complete absence of power—meaning no LED indicators on the remote, no display on the machine, and no response from the physical power button—indicates a to…
-
how do i clean the main fan part inside the dyson tp07 loop? it looks dusty in there
The dust accumulation you see inside the TP07 loop amplifier is caused by the Venturi effect. While the HEPA and carbon filters capture most particles, a small…
-
my tp07 is on auto mode but the fan speed keeps ramping up to max for no reason
The Dyson Purifier Cool TP07 relies on a high-precision laser particle sensor located behind the front grille to determine the air quality in real-time. When t…