Lawn Mowers
Push mowers, riding mowers, and self-propelled models -- will not start, cuts uneven, blades stuck, battery dies fast, and self-propel stopped working.
-
how do i store my ego mower for the winter? can i just leave it in the shed?
Proper storage prevents rust. Follow these steps. Procedure: Remove the battery pack. Store it separately in a dry, room-temperature location. Clean …
-
ego mower self propel isn't working, the wheels just spin freely. did i break it?
Grass or debris is likely jammed around the drive shaft. It's a common clog. Fix it: Remove the battery pack. Tip the mower safely. Inspect the drive…
-
can my teenager use the ego lawn mower? what's the age requirement?
The minimum age requirement for operating this lawn mower is 14 years old. If your teenager meets this age requirement, here is how to proceed safely…
-
what's the right way to clean under my ego power+ mower? i don't want to mess up the motor.
Yeah, you gotta clean it after each use, but you have to do it safe. Grass gunk promotes rust. Here's the drill: Shut the mower off and wait for the …
-
my ego mower is leaving clumps of grass underneath, it's not mulching properly. how do i fix this?
Wet grass is clogging the deck. The mower can't mulch effectively when the grass is damp. Fix: Stop mowing and wait for the grass to dry completely. …
-
how steep of a hill can i mow with my ego self propelled mower? i'm worried about tipping.
You should not mow any slope greater than 15 degrees. That's the absolute limit for safety. Here's what you need to do: Before mowing any slope, use …
-
ego lm2135sp mower starts but then shuts off immediately with an orange flashing light, what's that mean?
The overload protection has activated. The mower is trying to cut too much grass at once. Fix it: Release the blade control handle to stop the mower.…
-
my ego power+ mower won't start at all, no lights or anything, what gives?
Dead or improperly seated battery. It's the most common cause. Fix it: Press the battery release button and pull the pack straight out. Check the bat…
-
after storing my z6 for the winter, it won't turn on at all, no lights on the display
DIAGNOSIS A completely dead mower after storage usually points to two things: deeply discharged batteries, or a poor connection where the main batter…
-
one side of my z6 drives slower than the other, it pulls to one side when i'm trying to go straight
DIAGNOSIS When one side drives slower, it's almost always a calibration issue with the drive control levers, not a mechanical failure. The sensors th…
-
how do i clean the underside of the deck on this thing, grass is caked on super thick
DIAGNOSIS Wet or stringy grass building up under the deck is common, especially in damp conditions. That buildup reduces cutting quality, strains the…
-
the battery indicator on my z6 flashes red even after a full charge, won't let me mow
DIAGNOSIS A flashing red battery icon usually means the mower's computer has detected a problem with one or more of the battery packs, like a voltage…
-
i get an error code e1 or e2 on the display of my ego z6, what does that mean?
DIAGNOSIS The E1 and E2 codes are communication errors. E1 typically means the display can't talk to the main controller, and E2 often points to a pr…
-
my z6 is making a loud clicking or grinding noise from underneath when i try to drive
DIAGNOSIS A loud mechanical grinding or clicking from the drive area, especially when you first start moving, usually points to a problem with the dr…
-
the blades on my z6 won't engage, i press the button and the light comes on but they don't spin
DIAGNOSIS The switch light coming on tells you power is reaching the switch, but the signal isn't getting to the blade relay or the PTO clutch itself…
-
my ego z6 just beeps three times when i try to start it and nothing happens, battery is full
DIAGNOSIS That three-beep sequence is the mower's safety system telling you something isn't right for startup. The most common culprit is the seat se…
-
my automower keeps getting stuck on slight slopes or dips, it just spins its wheels.
DIAGNOSIS The mower's grip is insufficient for the terrain. The factory-installed slick wheels lose traction on slopes, especially when damp. FIX Ins…
-
the cutting height adjustment knob just spins freely, won't change the height anymore.
DIAGNOSIS The plastic internal gear on the height adjustment mechanism is stripped. This is a common wear part. FIX You need to replace the cutting h…
-
it keeps saying 'outside working area' even though it's clearly inside the wire, what gives?
DIAGNOSIS The boundary signal is too weak where the mower is operating. This is often caused by a wire that is too deep or a wire break that hasn't f…
-
the app says 'no loop signal' and my 430xh is stuck in the middle of the yard.
DIAGNOSIS The mower has lost the boundary wire signal. This is usually a break in the boundary wire or a poor connection at the guide wire. FIX First…
-
how do i clean this thing? the underside is packed solid with wet grass every time it rains.
DIAGNOSIS Normal accumulation, but wet clippings compact into a dense mat. This strains the blade disc motor and reduces cutting efficiency. FIX Use …
-
the blades on my automower spin but it doesn't move, just sits there grinding a hole in the lawn.
DIAGNOSIS This is a drive motor failure. One or both of the drive wheels cannot engage. The wheel module gears are likely stripped. FIX Tip the mower…
-
getting an error 6 on my 430xh, says collision sensor obstruction but there's nothing in front of it.
DIAGNOSIS Error 6 is a false positive from the front bumper sensor. The microswitch inside the bumper housing is stuck or misaligned. FIX Press the b…
-
my automower 430xh is stuck at the charging station and just keeps beeping, won't go out to mow.
DIAGNOSIS The mower is docked but not charging. The most common cause is dirty or corroded charging contacts. FIX Power off the mower at the main swi…
-
where is the circuit breaker on the mj401e? i see a red button but pressing it does nothing.
DIAGNOSIS The red button is the circuit breaker reset. If pressing it yields no click and the mower is dead, the issue is elsewhere. FIX Follow the p…
-
i just assembled it and the safety lever feels stuck, won't press down to start.
DIAGNOSIS Incorrect assembly. The bail (safety start lever) is likely misaligned with its pivot point or the lower handle bracket is interfering. FIX…
-
the mower seems underpowered and bogs down in normal grass.
DIAGNOSIS Insufficient power delivery or excessive load. Check three items: cutting height, extension cord, and deck clearance. FIX Step one: Set the…
-
the handle on my sun joe 14 inch mower is wobbly and won't stay tight.
DIAGNOSIS The handle locking mechanisms are loose. The MJ401E uses two knobs that secure the handle into the upright position. FIX Lower the handle t…
-
how do i clean under the deck on this thing? grass is caked on solid.
DIAGNOSIS Wet or tall grass has built up inside the mower deck, impeding airflow and cutting efficiency. FIX Unplug the mower. Tip it back onto its r…
-
my mower makes a loud grinding or screeching noise when it runs.
DIAGNOSIS Metal-on-metal contact. The blade is likely hitting the debris shield or a foreign object is lodged in the blade housing. FIX Unplug the mo…
-
the blade on my mj401e spins but it's not cutting evenly, just tearing the grass.
DIAGNOSIS The cutting blade is dull or damaged. The MJ401E uses a single 14-inch steel blade that dulls quickly, especially near fences or on sandy s…
-
my sun joe mj401e mower just stopped working mid-job and now won't turn on at all.
DIAGNOSIS This is a loss of power. The most common cause is the circuit breaker on the mower tripping from overload or a clog. FIX Step one: Unplug t…
-
the wheels on my hrn216 feel wobbly and don't track straight anymore, making it hard to steer
DIAGNOSIS The wheel hub bushings are worn out, allowing excessive play between the wheel axle and the deck mounting bracket. FIX Replace the wheel hu…
-
my honda mower starts but then sputters and dies after about 30 seconds, won't stay running
DIAGNOSIS The carburetor's main jet or passages are clogged with old gas deposits. The engine runs on the fuel in the float bowl, then starves. FIX C…
-
i can't get the self-propel speed control lever on the handle to stay in the fast position, it just slips back to slow
DIAGNOSIS The friction washer or detent mechanism inside the speed control lever housing on the handle is worn or loose. FIX Tighten or replace the f…
-
my honda mower leaves strips of uncut grass even with a sharp blade, it's not bagging or mulching well
DIAGNOSIS The underside of the mower deck is clogged with compacted wet grass, disrupting the airflow needed for proper vacuum lift and discharge. FI…
-
the engine on my hrn216vka dies when i release the self-propel drive bar, it only runs if i'm holding it forward
DIAGNOSIS The problem isn't with the self-propel. The blade control bail return spring is weak or disconnected, so it's not keeping the bail engaged.…
-
my honda mower runs but sounds really rough and vibrates a lot more than it used to, especially at full throttle
DIAGNOSIS The engine mounting bolts have probably worked loose from vibration, causing the entire engine to shake against the deck. This is a frequen…
-
just got my new honda hrn216 and it's super hard to pull the starter cord, feels like it's locked up
DIAGNOSIS The blade control bail (the lever you hold to start and run the mower) is likely not fully engaged with the engine's flywheel brake. This s…
-
my honda hrn216vka mower starts fine but then the self-propel just stops working after a few minutes, what gives?
DIAGNOSIS The self-propel drive belt is likely slipping off its pulley or has stretched and worn out. This is the most common cause of intermittent o…
-
why does my mower leave streaks of uncut grass, especially on one side? i just sharpened the blade.
DIAGNOSIS Streaking is usually a deck height or leveling issue, not a blade sharpness problem. One side of the deck is lower than the other, so it sc…
-
can i use a different brand's 60v battery in my toro recycler? the compatibility is confusing.
DIAGNOSIS No, you cannot. The physical shape, the connector, and the communication protocol between the battery and the mower are proprietary to Toro…
-
the battery charger shows a solid red light and never turns green, even after a whole day. is my battery dead?
DIAGNOSIS A solid red light usually means the charger is trying to charge but can't complete the process. This often points to a battery that's deepl…
-
how do i clean this thing? the deck is packed with wet grass and it's starting to rust.
DIAGNOSIS The 'Recycler' design mulches finely, which can lead to more clumping and sticking, especially with damp grass. The packed debris traps moi…
-
my mower makes a horrible grinding noise from under the deck when i engage the blade, sounds like metal on metal.
DIAGNOSIS That's the sound of the blade hitting something it shouldn't. Either the blade is bent, loose, or there's a foreign object wedged between t…
-
i assembled my new toro recycler but the self-propel doesn't work, the wheels just drag. did i put it together wrong?
DIAGNOSIS Yeah, this one's common. During assembly, there's a critical step where you connect the drive cable to the rear wheels that people often mi…
-
the battery on my toro 60v says it's charged but the mower only runs for like 10 minutes then dies, is the battery already bad?
DIAGNOSIS Probably not a bad battery. This is usually a thermal cutoff. The battery or the mower's motor controller is overheating and shutting down …
-
my toro recycler just beeps three times when i try to start it and the blade won't spin, what's up with that?
DIAGNOSIS That's the mower's safety system telling you it's not in a ready-to-run state. The most likely cause is you're not holding down the safety …
-
how do i put the bag on my new honda hrn216? the clips aren't obvious.
You need to attach the frame to the fabric bag. Here's how:Take the assembled frame and install it into the fabric grass bag. Make sure the grass bag…
-
can i run my honda lawn mower in the garage to warm it up? it's cold out.
No. Yeah, this one's a major safety hazard. Never run it in an enclosed area like a garage, even with the door partially open. The exhaust contains p…
-
honda hrn216 making a horrible vibration and loud noise, blade hit a rock. what do i check?
You have a bent or damaged blade and likely a damaged blade holder. Striking objects causes severe engine damage not covered by warranty. Immediate a…
-
what oil do i use in my honda hrn216vka mower? manual is confusing.
For general use: SAE 10W-30. Honda recommends API service category SJ or later. Check the API label on the oil container. Other viscosities by temper…
-
how tight are the blade bolts supposed to be on a honda hrn216? i don't want them flying off.
They need to be torqued to a specific setting. If they're loose, the blades can be thrown, which is extremely dangerous. The required torque is 36 to…
-
my honda self propelled mower is leaving behind cut grass even with the bag on, what gives?
The grass bag is full or clogged. Empty it. If the problem persists, check these causes in order:Bag clogged: Wash the grass bag. Mower deck clogged:…
-
honda hrn216vka lawn mower leaking gas when i tilt it to check the blade, is this normal?
No. Fuel leakage during tilting means you tilted it to the wrong side. To prevent fuel leakage and carburetor flooding, you must always tilt the mowe…
-
my honda hrn216vka won't start, just makes a clicking sound when i pull the starter, what's wrong?
The engine likely has no oil or is severely overfilled. Check the oil level first. The mower ships without oil. Remove the oil filler cap/dipstick an…
-
the self-propel on my honda hrn216 feels like it's going way too fast, how do i slow it down?
You're applying too much pressure to the Smart Drive paddles. Ease up. The Smart Drive system has a variable speed transmission. The speed is directl…
-
can i run my honda lawn mower in my garage to warm it up on a cold morning?
No, you should never do that. It's extremely dangerous. Your mower's exhaust contains poisonous carbon monoxide gas, which you cannot see or smell. I…
-
what's the right oil for a honda hrn216vka lawn mower and how often do i change it?
Use SAE 10W-30 oil with an API service category of SJ or later. Change it per the maintenance schedule. Oil is a major factor for performance and eng…
-
just got a new honda hrn216 and it's blowing white smoke out the exhaust. did i break it already?
Yeah, this one's common with new mowers. It's not broken. The engine was run at the factory and some residual oil can get into the air cleaner. When …
-
my honda mower is shaking a lot more than usual and making a weird vibration noise. should i be worried?
Yes, you should be worried. The shaking and vibration noise are serious warning signs. The immediate cause is typically loose or damaged blade bolts.…
-
how do i change the blade on my honda hrn216vka? is it hard to do?
It's a straightforward job if you have the right tools and follow safety steps. You'll need a 14 mm (6-point) socket wrench and a torque wrench. Turn…
-
honda hrn216 self propelled mower is leaving behind cut grass when i'm trying to bag. bag isn't full. what gives?
This is almost always a clog or a dull blade issue. Empty the grass bag. Check that all four cutting height adjustment levers are set to the same pos…
-
my honda hrn216vka lawn mower won't start, just makes a clicking noise when i pull the cord. what's wrong?
Your mower was shipped without oil. Running it dry will seize the engine. Add the entire included bottle of oil to the engine. Screw the filler cap/d…
-
greenworks mower is vibrating a lot more than usual and sounds rough. is the blade loose?
That's a sign the blade is likely unbalanced, bent, or loose. You need to stop using it and check immediately. Safety first. Remove the battery pack.…
-
can i use my greenworks cordless mower to mulch leaves in the fall?
Yes, but with specific conditions. Use the mulch plug. The mower is designed for mulching when the optional mulch plug is installed, which blocks the…
-
my greenworks 40v lawn mower just stopped in the middle of mowing. no noise, nothing. help?
Battery is depleted or a safety interlock disengaged. Check the battery indicator. If no lights show, the battery is dead. Install a charged battery.…
-
greenworks mower battery flashes red when i try to charge it, won't charge. what does that mean?
The battery or charger has a fault. The red flash is an error indicator. Confirm the charger is plugged into a working outlet. Unplug the charger. Re…
-
is it okay to hose off my greenworks 40v mower to clean it?
No, don't hose it off. Yeah, this one's common. Direct water can wreck the motor and electrical parts. The right way is to remove the battery first. …
-
my greenworks cordless mower is leaving uncut strips of grass. blade seems fine.
The cutting height is uneven or the deck is clogged. First, check all cutting height levers. There's one on each wheel. Set every lever to the same n…
-
greenworks 40v mower handle won't lock into place, it just flops around. how do i fix it?
You need to properly unfold and lock the handle into its operating position. It won't start if it's loose. Stand behind the mower and lift the handle…
-
my greenworks 40v lawn mower won't start, just makes a clicking sound when i pull the handle, what's wrong?
The battery pack is not making proper contact or is discharged. The safety handle must be fully engaged. Press the battery release button and remove …
-
can i use the ego lm2135sp without the grass catcher, just side discharge
Yeah, you can, but you need to install the right part. It doesn't just run open. You have to install the side discharge chute. Find the side discharg…
-
my ego mower's blade stopped spinning but the motor still runs, what gives
The blade adapter or drive key has sheared. This is a safety feature to prevent motor damage. Disconnect the battery. Tilt the mower. Attempt to turn…
-
the grass catcher on my lm2135sp won't stay on, keeps falling off
The bag frame, mulch plug, or side discharge chute is not installed correctly, or the bag frame is damaged. Follow this checklist: Confirm the mulch …
-
ego power+ mower handle feels loose and wobbly, how do i tighten it
Loose hexagon socket screws on the handle assembly and beam assemblies are the fix. You need a hex key. Check these points: Tighten the 4 hexagon soc…
-
how do i change the cutting height on the ego lm2135sp, the lever is stuck
The height adjusting lever is likely jammed with grass clippings or debris. You'll need to free it up. First, make sure the mower is off and the batt…
-
my ego 56v mower is making a loud clicking or grinding noise from under the deck
Yeah, this one's common. It's almost always a foreign object caught in the blade or a damaged blade hub. First, safety: Disconnect the battery. Tilt …
-
self-propel on my ego lm2135sp is weak or intermittent, feels like it's dragging
The self-propelled unit's motor and gear assembly or drive belt is the likely cause. Diagnose in this order: Check the wheel assemblies (part number …
-
ego power+ lm2135sp won't start at all, nothing happens when i pull the lever, help
The switch assembly or the internal wire assembly has a bad connection. First, check the battery. Ensure it's fully seated in the battery cover assem…
-
where is the serial number on a greenworks 40v 21 inch mower? need it for warranty.
The serial number is on the product identification label. Location: On the mower deck. Product Shown: MO40L03. Model Number: LMF415. Required Informa…
-
my greenworks cordless mower just stopped in the middle of mowing and won't restart, battery light is still on.
Likely an overload or thermal protection trigger. The motor shut down to protect itself. Remove the battery to fully reset the mower's system. Check …
-
the blade on my greenworks mower seems wobbly or loose, is that normal?
No. A wobbly blade is dangerous and indicates a failed or loose blade adapter bolt. Remove the battery. Tip the mower correctly (control side up). Us…
-
can i use my greenworks 40v mower to mulch wet leaves in the fall?
No. The mower is not designed for this. Operation Condition: It is not for wet grass or leaves. Debris Type: It is not for loose, dry leaves or grave…
-
greenworks 40v battery won't click into my lawn mower, feels loose.
Check for obstruction or misalignment in the battery port. Inspect the battery terminals and the mower's contact points for dirt, grass clippings, or…
-
how do i clean under my greenworks cordless mower deck? it's caked with grass.
You'll want to clean that out to keep your cut even and prevent corrosion. Here's the safe way to do it. First, turn the mower off and pull out the b…
-
greenworks 40v mower is making a horrible grinding noise when i try to mow, sounds like metal on metal.
Yeah, this one's common. You've almost certainly got a rock, stick, or a wad of packed grass jammed under the deck, hitting the blade. Stop immediate…
-
my greenworks 40v lawn mower won't start when i pull the handle, battery is charged, what gives?
Most likely cause is the operator presence control handle isn't fully depressed. This is a safety lockout. Ensure the battery is correctly inserted a…
-
ego power+ mower blade suddenly stopped spinning but the motor still runs, what gives?
The blade adapter hub or drive key has sheared. Disconnect the battery immediately. Inspect the blade, blade bolt (part number 5640321002), and the p…
-
can i use my ego lm2135sp without the grass catcher, just side discharge?
Yes. Install the side discharge chute. Remove the grass catcher bag frame (part number 3705442002) and the grass catcher itself (part number 38001090…
-
my ego lawn mower is leaving uneven strips of uncut grass, what should i check?
Check blade condition, deck clearance, and cutting height consistency. Inspect the blade (e.g., part number 3707066004) for damage, dullness, or imba…
-
ego mower won't go into self-propelled mode, the button does nothing. fix?
Yeah, this one's common. Either the switch actuator is jammed or the drive motor wire is disconnected. First, check that the switch actuator (part nu…
-
the handle on my ego mower feels loose and wobbly, how do i tighten it?
Tighten the hexagon socket screws at the handle pivot points. Locate the four hexagon socket screws (part number 5620161005) and four prevailing torq…
-
how do you change the blade on an ego lm2135sp? i can't figure out how to lock it.
You need to immobilize the blade hub. First, disconnect the battery. Tip the mower on its side, air filter side up. Place a block of wood between the…
-
ego self-propelled mower making a loud grinding noise when i engage the drive, what's broken?
The self-propelled gear set or motor assembly is likely damaged. Inspect the self-propelled unit (part number 2826067001). Check the motor & gear ass…
-
my ego power+ lm2135sp mower won't start at all, no lights or anything, anyone know why?
The battery isn't seated or the main fuse is blown. Push the battery release button and remove the battery, then reinstall it firmly. Check the 4908 …
-
the battery release button on my ego mower feels stuck and i can't get the battery out. help?
The release button (part 201-13) is likely jammed by debris or has a broken spring. First, try cleaning. Remove any visible grass or dirt around the …
-
can i use a mulching plug with the side discharge chute on my ego lm2135sp at the same time?
No. The parts list specifies the mulch plug (part 5), side discharge chute (part 4), and grass catcher (part 3) as separate, single-quantity attachme…
-
ego power+ mower is leaving uncut strips of grass. blade seems fine, what gives?
Yeah, this one's common. It's usually the deck height being uneven or the blade deck itself is out of level. The height adjusting lever (part 32) con…
-
my ego mower handle is wobbly and loose, feels unsafe. how do i tighten it?
The handle attaches via clamps and bolts to the beam assemblies. Tighten the hexagon socket screws. Locate the clamp (part 202-20) and clamp block (p…
-
ego mower self-propel function stopped working, wheels just freewheel. how do i fix the drive?
First, check the drive engagement system in the handle. The switch actuator (part 202-13 or 202-21) connects to the switch electric assembly (part 20…
-
how do i replace the blade on my ego lm2135sp? it hit a rock and is bent.
You'll need to secure the blade from spinning and remove the hubcap. Here's how. Disconnect the battery pack. Tip the mower on its side, with the air…
-
ego self-propelled mower making a grinding noise from the wheels, sounds awful. is the drive broken?
The self-propelled unit has a specific gear set (part 203-3) and a motor & gear assembly (part 203-2). A grinding noise indicates gear damage or a fa…
-
my ego power+ lm2135sp mower won't start at all, no lights or anything. battery is charged, what's up?
Check the fuse. The 4908 Fuse PCBA (part 201-14) is a common failure point. It's inside the power unit. Remove the battery. Open the battery cover as…
-
greenworks 40v mower handle feels loose and wobbly. how do i tighten it?
The handle has folding knobs that might not be fully locked. Let's get it solid. You'll need to locate the handle adjustment knobs. Here's the step-b…
-
the battery on my greenworks mower dies super fast, like 10 minutes. is the battery bad or is it me?
It's likely your mowing conditions, not a bad battery. Here's the troubleshooting order: Check your grass. Mowing tall, wet, or dense grass cuts runt…
-
can i use my greenworks 40v lawn mower on a hill? the manual is confusing.
Yes, with a 15-degree maximum slope limit. Exceed that, you risk loss of control and personal injury. FIX Do not mow across the slope. Mow up and dow…
-
how do i clean under the deck of my greenworks 40v mower? it's caked with wet grass.
Procedure: Clean after every use, especially after mowing wet grass. Required steps: Remove the battery pack. Tip the mower onto its side, with the a…
-
my greenworks cordless mower makes a horrible grinding noise when i engage the blade. is the motor toast?
Yeah, this one's common. It's almost never the motor. You've got something hard caught between the blade and the deck, or the blade itself is hitting…
-
greenworks 40v mower is leaving streaks of uncut grass. blade seems fine. what gives?
Your cutting height is uneven or you're mowing too fast. Here's the fix, in order of likelihood: Check all four wheels. The height adjustment levers …
-
my greenworks 21 inch cordless mower suddenly stopped while i was mowing. now it won't restart, any ideas?
This is almost always the battery. It either ran out of charge or overheated and shut down. Here's what you do: First, let the mower and the battery …
-
my greenworks 40v lawn mower won't start at all, just makes a clicking noise. what's wrong?
The battery pack isn't seated correctly or the safety start switch is disengaged. FIX Make sure the battery pack is fully inserted into the mower dec…
-
ego mower blade stops spinning when i hit tall grass, but the motor is still running.
The blade bolt has loosened or the blade adapter is stripped. Stop immediately. Disconnect the battery. Check the prevailing torque hexagon lock nut …
-
can i use the mulch plug and side discharge chute at the same time on my ego lm2135sp?
No. They are mutually exclusive attachments. The mower is designed for one of three configurations: Mulching: Install the mulch plug (part number 312…
-
ego lawn mower handle is wobbly and loose, how do i tighten it?
The hexagon socket screws securing the handle assembly have likely loosened. You'll need a hex key. Locate the four hexagon socket screws (part numbe…
-
my ego mower's grass bag won't attach properly, it keeps falling off.
Diagnosis: The bag frame is damaged or not aligned with the rear cover hooks. Fix: Inspect the bag frame (part number 3705442002) for bends or cracks…
-
ego mower self propel just stopped working mid-mow, wheels won't drive.
Yeah, this one's common. Either the drive cable came loose or the self-propelled unit's motor failed. First, check the connecting rod assembly (part …
-
how do i replace the blade on my ego lm2135sp mower?
You need the correct blade and a wrench. Use blade part number 3707494002 or 3707130003. Disconnect the battery. Tip the mower on its side with the d…
-
ego self propelled mower making a grinding noise from the wheels, what's wrong?
You've likely got debris packed into the self-propelled gear set, or a gear is worn. First, tip the mower on its side (discharge chute away from you)…
-
my ego power+ lm2135sp lawn mower won't start, the battery is charged. help?
The safety switch actuator or the main electric assembly is faulty. Check the switch box set first. Inspect the switch actuator (part number 31297140…