Dryers (Page 2)
-
how do i clean the moisture sensor strips inside the drum? they look gross and i think it's messing up the auto-dry cycles.
You've nailed it. Those two metal strips on the back wall of the drum are the moisture sensors. They work by sensing the tiny electrical conductivity…
-
the wi-fi connection keeps dropping, won't stay connected to the smartthings app.
Yeah, this one's common with a lot of smart appliances. The wireless module in the dryer can be finicky, especially if your home Wi-Fi router is on t…
-
clothes are still damp after a full cycle, takes like 2 or 3 runs to get anything dry.
Inadequate heat. The drum is tumbling, but the air isn't hot enough to evaporate the moisture. The most frequent causes are a clogged vent (again), a…
-
it's making a loud scraping or squealing noise, only when the drum is turning.
That's almost certainly worn-out dryer drum support rollers. They're plastic wheels with a rubberized outer ring that the heavy drum rides on. When t…
-
the display on my gfd55essnww is completely blank, no lights, nothing. won't start at all.
A totally dead control panel usually points to a lack of power getting to the main control board. It's not getting the 120V it needs for the brains o…
-
my ge smart dryer just says 'check vent' and stops after a few minutes, what does that mean?
That's the dryer's vent restriction sensor kicking in. The machine detects too much back pressure, meaning the hot, wet air can't escape properly, so…
-
the sensor dry cycles always leave clothes damp, i have to run it twice. what's the point of the sensor?
The moisture sensors are the two or four metal bars visible inside the drum at the front. If they're coated with fabric softener residue, dryer sheet…
-
getting an f7 e1 error code, can't find it in the little manual. dryer just stops.
F7 E1 is a specific communication error. It means the main control board (the user interface you touch) is not talking to the motor control board. It…
-
door won't latch shut properly, i have to really slam it and sometimes it still pops open mid-cycle.
This is almost always a worn or misaligned door strike—the little metal hook on the door that catches the latch inside the door frame. Over time, it …
-
trying to connect it to the maytag app but it just won't find the dryer during setup. wifi in the laundry room is fine.
The onboard WiFi module in these dryers is notoriously finicky about network types. It often fails to connect or see networks that are 5GHz, have cer…
-
the 'check filter' light won't turn off even after i've cleaned the lint screen completely.
The sensor for that light isn't actually checking for lint—it's a timer. It illuminates after a set number of cycles to remind you to clean the filte…
-
it's making a loud thumping or grinding noise, sounds like it's coming from the back. just started today.
A loud thump or grind from the rear is classic failed dryer drum support roller. These are plastic wheels with bearings that the back of the drum rid…
-
dryer is running but not heating at all, clothes are just tumbling damp. my model is the med6230rhw.
The drum spins but no heat almost always points to a failed thermal fuse or a blown heating element. On these Maytags, the thermal fuse is a common f…
-
my maytag smart dryer just shows 'pf' on the screen and won't start, what does that even mean?
Yeah, this one's common. "PF" stands for Power Failure. The dryer's electronics detected a brief interruption or surge in your home's power, and it's…
-
my revlon one-step 2.0 smells like burning plastic or electronics every time i use it now
DIAGNOSIS: That smell is usually one of two things: hair/product debris burning on the heating element, or, more seriously, internal electrical compo…
-
the barrel of my one-step is wobbling where it connects to the handle, is it going to break off?
DIAGNOSIS: This is a physical stress failure. The plastic housing where the barrel connects to the handle has likely cracked or the internal screws h…
-
how do i clean the bristles on the revlon one-step? they're full of hair and product gunk
DIAGNOSIS: Product buildup and wrapped hair on the nylon and ionix bristles is normal, but it reduces performance and can smell burnt when heated. FI…
-
the revlon one-step 2.0 gets way too hot on my hair even on the low setting, it feels like it's burning
DIAGNOSIS: The temperature regulation might be faulty. Some units have a reported issue where the low heat setting doesn't properly reduce the power …
-
my hair keeps getting sucked into the back of the revlon one-step brush, it's tearing and snapping my hair
DIAGNOSIS: This happens when the air intake grille (the holes near the handle) doesn't have its protective filter in place, or when the filter is clo…
-
the cool shot button on my volumizer plus doesn't stay on when i press it, i have to hold it down
DIAGNOSIS: This is a mechanical failure of the button's latching mechanism. The Cool Shot button is supposed to click and stay depressed to keep the …
-
why does my revlon one-step 2.0 make a loud grinding noise when i turn it on? sounds like something's stuck
DIAGNOSIS: Yeah, this one's common. That grinding or rattling noise is almost always caused by hair, lint, and product buildup getting sucked into th…
-
my revlon one-step 2.0 just stopped turning on, no lights or anything, i've only had it a few months
DIAGNOSIS: This is usually a power supply or thermal trip issue. The most common cause is a blown internal thermal fuse that's designed to protect th…
-
how do i get the stupid 'clean filter' light to turn off on my whirlpool dryer? i've cleaned it a bunch
DIAGNOSIS: That light isn't triggered by a sensor; it's a simple timer. It comes on after a set number of cycles (usually around 30-40) as a reminder…
-
it's making a high-pitched squealing or squeaking noise, only when the drum is spinning
DIAGNOSIS: That squeal is almost always dry bearings on the idler pulley or the drum support rollers. The idler pulley puts tension on the drive belt…
-
dryer drum spins but no heat at all, clothes are just cold and damp. whirlpool electric vented
DIAGNOSIS: No heat with normal spinning means the heating circuit is open. The prime suspects are the thermal fuse (a one-time safety cutoff) or the …
-
the lint filter on my wed5000dw feels like it's barely catching anything, and i see lint in the drum after a cycle
DIAGNOSIS: That's by design, unfortunately. The lint filter on this model is notoriously inefficient, especially with finer lint from synthetics. A l…
-
suddenly getting an f01 error code on my whirlpool dryer, what does that mean?
DIAGNOSIS: F01 is a generic "control communication failure" error on these models. It means the main control board (the brain) isn't getting a proper…
-
the dryer heats but it takes forever to dry clothes, like two or three cycles. wed5000dw
DIAGNOSIS: Yeah, this one's common. The dryer heats, so the element is working. The most likely culprit is a clogged venting system—either the lint s…
-
dryer makes a loud thumping noise like a shoe is in there, but it's empty. whirlpool wed5000dw
DIAGNOSIS: That's almost certainly the drum support rollers wearing out. They're plastic wheels with a rubber tire, and when the rubber degrades or t…
-
my whirlpool wed5000dw dryer just beeps and won't start at all, the lights are on but nothing happens when i press start
DIAGNOSIS: The dryer is likely refusing to start because the door safety switch is failing or the door isn't making good contact. The beep is a very …
-
dyson dryer works but the air doesn't feel as powerful as it used to, even on the max setting
This is a classic symptom of restricted airflow. The motor is working, but it's struggling to pull air through. The primary suspect is, yet again, th…
-
the magnetic filter on my hd08 won't click back in securely, it just falls off now
The plastic tabs on the filter housing or the corresponding slots on the dryer body have worn down or broken. This is a physical wear issue, often fr…
-
my dyson dryer smells like burning plastic or hot electronics when i use it, is it going to catch fire?
This is almost never the motor or wiring (which would be a serious fire hazard). It's almost always foreign material—a dust bunny, a hair, or a small…
-
how do you actually clean the inside of the dyson dryer nozzle? i see dust and lint in there and can't get it out
You're right to want to clean it—debris inside the attachments can get heated up and create a burnt smell. The nozzles aren't designed to be taken ap…
-
the cold shot button on my supersonic is stuck down and won't stay popped out, air is always cold now
The physical mechanism for the cold shot button has failed. It's a known point of wear. The button is designed to be held down for a burst of cold ai…
-
why does my dyson dryer keep cutting off after a few minutes on the highest heat setting? it just goes cold.
It's overheating and the thermal cut-out is doing its job. This is 99% a airflow problem caused by a clogged filter, not a faulty sensor. The is iden…
-
dyson hair dryer making a high pitched whining or grinding noise, sounds like a bearing is shot
Yeah, this one's common. The most likely culprit is something—usually a hair—wrapped around the impeller (the fan) inside the handle, throwing it off…
-
my dyson supersonic just stopped turning on out of nowhere, the light doesn't even come on when i plug it in
This is almost always a filter or power supply issue. The thermal cut-out can trip if the filter is blocked, or the power cord/connection at the hand…
-
there's a burning smell coming from my lg dryer, not like lint, more like hot plastic or rubber.
A hot plastic or rubber smell, especially if it's new or sudden, often points to a mechanical part overheating due to friction. The prime suspects ar…
-
the control panel on my dlex7900we is totally dead, no lights, nothing. but i hear a click when i press power.
You have power getting to the main control board (that's the click you hear), but the board itself isn't booting up or sending power to the display a…
-
my lg dryer is taking forever to dry a normal load, like over two hours. it's not throwing an error.
Extended dry times are almost always a heat flow problem. The dryer is working, but not getting hot enough, or the hot, moist air isn't escaping effi…
-
how do i clean the moisture sensor strips in my lg dryer? my clothes are still damp saying it's done.
The dryer is using its timed cycle, not the "Auto Dry" sensing, because the sensor strips inside the drum are coated with fabric softener residue or …
-
the wifi on my lg smart dryer keeps disconnecting and i can't control it from my phone anymore.
This is a frequent headache with smart appliances. The dryer's Wi-Fi module has a weak signal or can't maintain a stable connection to your home netw…
-
lg dryer dlex7900we just beeps three times and won't turn on when i press start, what gives?
The three-beep error usually means the door isn't being sensed as fully closed, even if it looks shut. The door latch or sensor isn't engaging. First…
-
why is my smart lg dryer so loud? it makes a loud thumping or banging noise during the cycle.
That rhythmic thumping is almost always a foreign object—like a coin, button, or hairpin—loose in the drum or caught in the blower wheel area. It get…
-
my lg dlex7900we dryer keeps showing OE error and won't start a cycle, what's wrong?
Your dryer is sensing a restriction in the exhaust vent system, which is a common and often easily fixed issue. The OE code means it can't push air o…
-
getting a dE error code on my samsung dryer, can't get it to go away.
"dE" stands for "Door Error." It's similar to the three-beep issue but is the electronic version stored in the control board's memory. It means the d…
-
how do i clean the moisture sensor strips inside the drum? my dryer keeps stopping early saying clothes are dry when they're not.
Those two metal or plastic strips on the inside top-front of the drum are moisture sensors. They work by detecting the slight electrical conductivity…
-
the control panel on my samsung dryer is completely dead, no lights, no response, but i hear a hum.
A dead panel with a humming sound points to power reaching the main control board, but the board itself not initializing or a critical safety device …
-
clothes are still damp after a normal cycle, takes two runs to dry anything.
Inadequate drying is almost never the dryer's 'heating' part failing first. It's almost always an airflow problem. The hot air can't get through the …