All questions — page 134
Browse by Problem
-
how do i clean the inside? the top has this brown splattered film that won't come off
The brown splattered film on the ceiling of your Farberware FMO11AHTBKB is a result of "carbonized lipid buildup." When food splatters during the heating proce…
-
it makes a loud humming or buzzing noise when it runs but the plate still spins
The noise is from the magnetron cooling fan or a vibrating component. A loud, consistent hum points to the high-voltage diode or transformer. Check for foreign…
-
the interior light in my fmo11ahtbkb won't turn on when the door opens or during cooking, is it burnt out?
The most common cause for a dark interior in the Farberware FMO11AHTBKB is a failed 25-watt T7 halogen bulb. Unlike modern LED arrays, these filaments are frag…
-
my farberware microwave just beeps three times and won't start when i hit the cook time buttons
The three-beep sequence on the Farberware FMO11AHTBKB is a specific error signal indicating a "Logic Lock" or a failure in the membrane switch communication. W…
-
why does the exhaust fan on the bottom run for like 5 minutes after i'm done cooking?
That's normal and by design. It's a cooling-down period for the magnetron (the part that generates the microwaves) and other components. The fan continues to r…
-
the door on my compact microwave feels loose and doesn't always latch shut firmly
The hinge mechanism or the door latch assembly is likely worn or out of alignment. These doors get opened and closed thousands of times, and the plastic compon…
-
it keeps showing an H97 error code on the display, what does that mean?
H97 (or sometimes just H-97) is a communication error between the main control board and the touch panel/operation board. It means the microwave's brain isn't …
-
how do you clean the inside of this thing? the top looks like it has a brown stained coating that won't come off
That's not a stain, it's the fluorocarbon coating on the interior walls starting to break down from heat and splatter. Once it gets rough and discolored, it tr…
-
there's a really loud humming or buzzing noise coming from my microwave, way louder than the fan
That's usually the transformer humming excessively. It can happen as the microwave ages, or if it's operating on a slightly low voltage from your outlet. It's …
-
the number pad on my nn-sn68ks is totally unresponsive, only the start/+30 sec button works
This is typically a control panel lockout, not a hardware failure. The Safety Lock (often called Child Lock) feature is almost certainly enabled, disabling all…
-
my panasonic microwave starts for a few seconds then just stops and beeps, the turntable isn't moving
The microwave is detecting an obstruction or a failure in the turntable system. The most common cause is the roller guide (the little plastic ring the plate si…
-
just got this panasonic microwave and the clock is flashing 12:00, it won't let me start anything
This is the default power-on state. The microwave has lost its memory for the time, usually from being unplugged or after a brief power outage. You just need t…
-
the sensor cook functions keep overcooking my popcorn or melting my butter.
The humidity sensor is being triggered incorrectly, often because you're using the wrong container or the room is too humid. For popcorn, always use a microwav…
-
food heats unevenly in this microwave, some parts are boiling and others are cold.
The Breville Smooth Wave BMO850BSS is designed as a "turntable-free" microwave. Unlike traditional units that rotate the food through a stationary beam of micr…
-
the clock on my breville microwave resets to 0:00 every time i unplug it, is the battery dead?
The Breville Smooth Wave BMO850BSS is designed with a volatile memory system for its clock function. Unlike a traditional wall clock or some high-end ovens, th…
-
how do i clean the inside roof of this microwave? it has that brown splatter and won't come off.
The splatter is baked-on grease and food. The stainless steel interior can be cleaned, but the textured 'roof' around the light and vents is tricky. Heat a bow…
-
my smooth wave makes a loud humming or grinding noise when it runs, not the normal fan sound.
The loud humming or grinding noise in the Breville Smooth Wave BMO850BSS is typically caused by a failure in the cooling fan assembly or an obstruction in the …
-
the control panel on my breville microwave is completely unresponsive, no lights, nothing.
Total power failure. The most common cause is a tripped thermal fuse inside the unit or a loose power cord connection at the wall. Check your kitchen circuit b…
-
why does my breville smooth wave smell like burning plastic when i use it?
You're likely smelling overheated plastic from a foreign object inside the cavity or a packaging tag left on the unit. It's not the microwave itself burning. I…
-
my breville smooth wave microwave just beeps three times and won't start cooking, what's the deal?
The microwave is detecting the door isn't fully closed or the latch switch is failing. Three beeps is its standard 'door open' alert. First, check the door is …
-
the clock on my whirlpool microwave resets to 12:00 every time i have a power flicker.
That means the internal clock/control board doesn't have a backup power source like a capacitor holding a charge. It's a common 'feature' on many basic models—…
-
there's a loud humming or buzzing noise when my microwave runs, but it still heats food.
That's typically the sound of the cooling fan motor struggling. It's located behind the rear panel and can get noisy if its bearings are worn or if it's hittin…
-
how do i get the charcoal filter out of this thing to replace it? i can't find any latch.
It's tucked up inside the vent chamber and isn't meant for frequent replacement unless you're in recirculating mode. People often miss it because it's not obvi…
-
the touchpad on my over-the-range microwave is completely unresponsive, none of the buttons work.
This is usually a failure of the membrane touchpad or its connection to the main control board. Spills or grease seepage over time can damage the pad. Unplug t…
-
my whirlpool microwave keeps tripping the circuit breaker in my kitchen when i use it.
The microwave is drawing more current than the circuit can handle, which points to either an overloaded circuit or, less commonly, a short inside the microwave…
-
the light under my microwave won't turn on with the touchpad buttons, but the microwave works fine.
You've likely got a burned-out halogen bulb. They're high-heat bulbs and have a finite lifespan, especially if you use the under-cabinet light a lot. First, co…
-
the fan on my whirlpool hood microwave comes on by itself and i can't turn it off, what gives?
This model has an automatic fan feature tied to humidity. If it senses high moisture from cooking (like boiling pasta), it'll kick on the vent fan to help clea…
-
my whirlpool microwave just shows a flashing 'FF' code and won't start, what is that?
That's a control board communication failure. The main board isn't talking to the touchpad board properly, usually because of a loose connection or a failed bo…
-
the sensor cook functions burn everything. popcorn setting leaves half burnt, half unpopped kernels.
The GE JES1097SMSS utilizes a humidity-based sensor cook system designed to detect the release of steam from food to calculate the remaining cook time. When th…
-
i get an 'F2' error code on the display sometimes, what does that mean?
The F2 error code on the GE JES1097SMSS indicates a critical failure or "out-of-range" reading from the temperature sensing thermistor. This sensor is responsi…
-
my microwave's turntable won't spin at all, food heats unevenly. it just sits there.
The failure of the turntable to rotate in the GE JES1097SMSS is typically caused by a mechanical disconnect between the motor and the glass tray. In most cases…
-
how do i clean the inside roof of this microwave? it's got splatter baked on and the manual says not to scratch it.
The "roof" of the GE JES1097SMSS is not a solid metal surface; it features a critical component called the waveguide cover (often referred to as the mica sheet…
-
there's a loud humming or buzzing noise when my microwave runs, it wasn't this loud before.
The loud humming or buzzing noise in the GE JES1097SMSS is typically caused by one of two mechanical failures: a failing cooling fan motor or a misalignment of…
-
the wifi on my ge smart microwave keeps dropping and won't reconnect to my home network.
The GE JES1097SMSS utilizes a 2.4GHz Wi-Fi radio integrated into the main control board. Because the microwave is essentially a giant Faraday cage—a metal box …
-
why does my jes1097 keep beeping three times after it finishes cooking? it's driving me crazy.
The three-beep sequence at the end of a cooking cycle on the GE JES1097SMSS is a specific alert indicating a "door open" or "incomplete latch" state. While the…
-
my ge smart microwave just shows a blank screen and won't respond to any buttons, what's wrong?
Main control board failure. This is the most common cause of a completely dead unit with a blank display. Unplug the microwave for five minutes. Plug it direct…
-
door won't close all the way on my lg neochef, it feels like it's hitting something
An obstruction is blocking the door latch mechanism, or the door seal (gasket) is misaligned or folded over. Inspect the door's inner edge and the correspondin…
-
the popcorn button always burns my popcorn, is it just broken?
The 'Popcorn' sensor button is calibrated for a specific weight and bag type (typically 3.0-3.5 oz conventional bag). Using smaller bags, different brands, or …
-
can't get the smart things app to connect to my neochef, it just times out every time
The most common cause is an incorrect Wi-Fi setup sequence or a 5GHz network incompatibility. The LMC0975ST only connects to 2.4GHz Wi-Fi networks. Checklist: …
-
the turntable in my lmc0975st makes a loud grinding noise and sometimes just stops turning
Debris (food crumbs, hardened spillage) is lodged in the turntable track or the roller guide assembly is misaligned or broken. Remove the glass tray and the su…