All questions — page 135
Browse by Problem
-
i get an f2 error when i try to use the sensor cook functions, what does that mean?
Error code F2 indicates a fault with the humidity sensor. The sensor cannot detect steam properly, so all automatic sensor cooking, reheating, and defrost mode…
-
the easyclean coating inside my neochef is turning brown and sticky, is it ruined?
The ceramic enamel (EasyClean) interior has absorbed grease and food spatter from normal use. The sticky residue is polymerized grease, not a damaged coating. …
-
lg neochef keeps beeping 3 times after it finishes cooking, how do i make it stop?
The three-beep sequence occurring at the end of a cooking cycle on the LG NeoChef LMC0975ST is not a mechanical failure or an error code; it is the factory-def…
-
my lg neochef microwave just shows '88:88' on the display and won't respond to any buttons, what do i do?
The "88:88" display on the LG NeoChef LMC0975ST is a symptom of a logic hang or a "frozen" state in the main control board. This is not a traditional error cod…
-
how do i get the damn burnt popcorn smell out of this samsung microwave? the usual tricks aren't working.
The smell is likely stuck in the grease filter or has seeped into the charcoal filter (if you have recirculating mode enabled). This model has a dual filter sy…
-
the touchpad on my samsung microwave is super unresponsive, have to press buttons multiple times, especially the number pad.
This is usually caused by a slight gap or moisture barrier between the touchpad membrane and the control board, often due to a loose connection, or less common…
-
my microwave just stopped working mid-cycle, no display, no power, nothing. checked the outlet and breaker and they're fine.
A complete, sudden loss of power points to the thermal fuse (also called a thermal cut-off). It's a one-time safety device that blows if the unit overheats, of…
-
the led lights under my samsung microwave are really dim or flickering, can i replace them myself?
The under-cabinet LED light strip is failing. On this model, it's an integrated strip, not a standard screw-in bulb. Individual LEDs can dim or die over time. …
-
the sensor cook function on my me21m706bas always seems to undercook everything, it's basically useless.
The humidity sensor isn't getting an accurate reading, usually because the interior isn't completely clean or you're using the wrong type of cookware. Steam fr…
-
i get an 'e-1' error code when i try to start cooking, what does that mean on this samsung microwave?
E-1 indicates a door switch problem. The microwave's safety system isn't detecting that the door is properly and fully closed. It could be a faulty switch, som…
-
the vent fan on my samsung over-the-range microwave is so loud it sounds like a jet engine, even on the low setting.
That roaring or rattling noise usually means the centrifugal fan wheel (the squirrel cage blower) has come loose on its motor shaft or something is obstructing…
-
my samsung me21m706bas microwave just shows a blinking '88:88' on the display and won't respond to anything, what's the deal?
Yeah, this one's common. The control board is temporarily locked up or has lost power, often after a brief power surge or outage. It's not a hardware failure, …
-
there's a loud humming or buzzing noise from my toshiba microwave even when it's not cooking
The cooling fan is running continuously due to a faulty control relay or a stuck switch, or the transformer is vibrating abnormally. First, ensure you haven't …
-
the number pad on my toshiba microwave is super unresponsive, have to press really hard
The Toshiba EM131A5C-BS utilizes a capacitive membrane switch overlay. This design relies on a thin layer of conductive material that triggers a signal when pr…
-
my toshiba em131 beeps three times and won't start when i press start, door is shut
The control unit isn't receiving a proper 'door closed' signal from all the interlock switches. The triple-beep is a standard error sequence. Press firmly on t…
-
the clock on my toshiba microwave keeps resetting to 0:00 every time i unplug it
The internal backup battery on the main control board is dead. Its sole job is to maintain clock memory during brief power outages. There is no user-replaceabl…
-
i get a burning plastic smell from my toshiba em131 when i use it, not from food
Spilled food or grease is burning on the waveguide cover (the mica or cardboard-like panel on the right side wall inside the cavity). Unplug the microwave. Rem…
-
my toshiba microwave light stays on all the time even when the door is closed
The door switch assembly is faulty. A microswitch that tells the control board the door is closed is stuck in the 'on' position or has failed. Check for obviou…
-
the turntable in my toshiba em131 spins super slow or gets stuck, it's not turning right
The roller guide or hub underneath the glass plate is dirty with grease/food debris or is cracked/worn, creating drag. Remove the glass tray and the underlying…
-
my toshiba em131 microwave just stopped and shows F-11 on the screen, what is this?
The control board has lost communication with the keypad/touchpad unit. It's a common internal wiring or connection fault. Unplug the microwave for 5 minutes. …
-
door on my panasonic microwave won't close all the way unless i really slam it, latch feels sticky
Sticky or resistant door closure is almost always caused by a buildup of grease and grime on the door latch hooks (on the door) and the corresponding strike pl…
-
the clock on my microwave keeps resetting to 0:00 every time there's a brief power flicker
This model doesn't have a backup battery for the clock/memory. It relies on constant, minimal standby power from the wall outlet to keep the microcomputer's me…
-
panasonic microwave makes a loud humming or buzzing noise the whole time it's running, not just the fan
A constant, loud hum or buzz that's distinct from the normal fan and turntable motor sounds usually points to the high-voltage diode or the transformer. With P…
-
the sensor cook on my nn-sn966s always overcooks my food, it's useless. what am i doing wrong?
The sensor (auto cook) works by detecting steam humidity. If you're covering the food too tightly with plastic wrap or a lid, or using a container that doesn't…
-
how do you clean the inside roof of this panasonic microwave? it has that brown splatter on the inverter thing
The brown splatter on the flat, rectangular metal panel on the ceiling is baked-on food hitting the waveguide cover. That panel protects the magnetron waveguid…
-
the turntable in my panasonic microwave spins for a second then stops, makes a grinding noise
The drive coupler—that's the little three-pronged plastic piece under the glass tray that connects the motor to the tray—is either broken, worn out, or the mot…
-
panasonic nn-sn966s keeps tripping my kitchen gfci outlet every time i try to use it
The microwave is drawing a sudden, high current that's exceeding the GFCI's sensitivity. This is often caused by a minor internal arc or a failing component, m…
-
my panasonic inverter microwave just shows three zeros on the display and won't heat anything, what's wrong?
That display means the control lock or child safety lock is almost certainly turned on. It's a common first-day or accidental button-press issue. You just need…
-
the third rack on top doesn't seem to get anything clean, glasses come out spotted or still dirty
The Samsung Bespoke DW80B7070AP features a specialized third rack designed for cutlery and small espresso cups, but its position makes it highly susceptible to…
-
i get an 'e1' or 'e3' error code on the display after it runs for a few minutes
The E1 and E3 error codes on the Samsung Bespoke AutoRelease DW80B7070AP indicate a failure in the water management cycle, specifically regarding the timing of…
-
the control panel is completely dead, no lights, no response, but i can hear a faint hum from inside
The presence of a faint hum combined with a completely dark control panel indicates that the appliance is receiving line voltage, but the logic circuit is fail…
-
the wifi keeps disconnecting on my smart dishwasher, i have to keep re-adding it in the app
The Samsung Bespoke AutoRelease DW80B7070AP utilizes a compact Wi-Fi module tucked behind the control panel, which is shielded by a thick stainless steel chass…
-
dishes are still wet and soapy at the end of the cycle, like it didn't rinse or drain properly
The presence of soapy residue and standing water on the dishes in the Samsung Bespoke DW80B7070AP indicates a failure in the evacuation phase of the wash cycle…
-
it's making a loud grinding or buzzing noise during the wash cycle, sounds like it's coming from the bottom
The grinding or buzzing noise emanating from the bottom of your Samsung Bespoke DW80B7070AP is almost certainly caused by a foreign object—such as a shard of b…
-
the auto release door on my dw80b7070ap doesn't pop open at the end of the cycle, it just stays closed
The AutoRelease function on your DW80B7070AP is failing to trigger. This is typically caused by the feature being accidentally turned off in the hidden setting…
-
my bespoke dishwasher just shows a big 'C' on the display and won't start any cycle, what is that?
The large 'C' on your Samsung Bespoke DW80B7070AP display indicates that the Control Lock (often called Child Lock) feature is active. This is a safety functio…
-
the sanitize light never comes on after a cycle, even on the sanitize setting. is it broken?
The sanitize indicator requires the final rinse water to reach 150°F and maintain it for a specific time. Failure indicates insufficient hot water supply. Ensu…
-
the third rack on top keeps falling down when i pull out the lower rack, it's super annoying.
The issue stems from a failure of the MyWay flexible third rack's locking detents to fully engage with the side-wall mounting brackets. In the Bosch 800 Series…
-
i keep getting an e24 error code on my bosch dishwasher, what does that mean and how do i clear it?
The E24 error code on the Bosch 800 Series (SHPM88Z75N) is a specific "drain-and-fill" fault. Unlike a simple water supply issue, E24 typically triggers when t…
-
the control panel on my bosch 800 is totally dead, no lights, no response, but i can hear a faint hum inside.
A dead control panel with internal power suggests a failed control panel unit or a loose internal connector, not a total power loss. First, confirm power at th…