Chainsaws (Page 2)
-
my husqvarna 460 rancher is smoking a lot more than usual and seems down on power, what's up with that?
Excessive smoke and power loss point to an incorrect fuel mixture or an engine running too rich. Fuel mix is wrong. This is the most likely cause. Yo…
-
the chain on my husqvarna 460 rancher keeps coming loose no matter how tight i get it, am i doing something wrong?
You're probably not tightening it in the right sequence, or the bar might be worn. Let's go step-by-step. First, loosen the two bar nuts (the ones th…
-
my husqvarna 455 rancher chainsaw won't start, just pulls and pulls. what gives?
This is almost always a fuel or air issue. Check the most common causes in order. Check the fuel. It must be fresh, high-octane gasoline mixed with a…
-
my ego chainsaw makes a horrible grinding noise and vibrates bad, only when the chain is moving. did i mess up the sprocket?
Grinding means metal-on-metal contact. Immediate causes: no bar oil, incorrect chain tension, or damaged drive components. STOP USING IT. Further use…
-
can i use my ego cordless chainsaw to cut down a small tree, like 10 inches thick? what's the safe way?
Yes, it's designed for basic felling. Safety is about technique, not just power. Follow the notch and backcut method. Felling Cut Sequence: Notch: Ma…
-
ego chainsaw headlights won't turn off, they just stay on dim after i use it. is my saw broken?
No, it's probably not broken. You've likely got it in the first brightness setting. The LED headlights have three states: off, bright, and brighter. …
-
replacing the chain on my ego cs1800e, which way does it go on? the manual is confusing.
Direction is critical. Incorrect installation causes poor cutting, no oiling, and rapid wear. Engage the chain brake. Push the chain-kickback brake h…
-
the chain brake on my ego cordless chainsaw keeps engaging by itself mid-cut, super annoying. how do i stop that?
Yeah, this one's common. You're likely bumping the brake handle forward with your left hand during use. It's a safety feature, but it's sensitive. Th…
-
ego power+ cs1804 chain isn't getting any oil, bar is smoking. how do i check the oiler?
First, check the oil level. The tank is empty or the chain is installed wrong. Immediate check: Look at the oil-inspection window. The oil must be ab…
-
ego chainsaw cs1800e chain keeps coming loose while i'm cutting, how do i tighten it right?
Yeah, that's a tension issue, and it's dangerous. You need to adjust it properly using the tool's built-in system. Here's how. First, push the chain …
-
my ego cs1804 chainsaw won't start at all, what's wrong?
Most likely the chain brake is engaged or the lock-off button is on. The saw won't run with the brake forward or the safety locked. Push the chain ki…
-
how tight should the chain be on my stihl ms 250? i feel like i'm always adjusting it.
It should be snug against the bar, but still pull freely by hand. Let me explain the right way to check and adjust it. First, always adjust the chain…
-
stihl ms 250 makes a high-pitched squealing noise when i first start it, goes away after a minute. normal?
Yeah, that's a classic sound—usually the clutch bearing. It's dry when cold. The clutch drum rides on a needle bearing. If it doesn't have enough gre…
-
can i use regular car motor oil for the bar oil on my stihl ms 250? i ran out of the stihl stuff.
No. Do not use car motor oil. Car oil is not formulated for chainsaw bar and chain lubrication. It lacks the tackifiers that make bar oil stick to th…
-
my stihl ms 250 is leaking bar oil all over my garage floor, even when it's just sitting. common problem?
Yeah, this one's common. It's usually not a catastrophic failure, just how the oiler system works when the saw is stored wrong. The bar oil tank is v…
-
how do i sharpen the chain on my stihl ms 250? feels like it's just rubbing now instead of cutting.
Your cutters are dull. You need to file them. Here's the fastest way. Secure the saw: Engage the chain brake. Clamp the bar in a vise. Match the file…
-
stihl ms 250 keeps dying as soon as i give it gas, runs fine at idle. anyone else have this?
This usually means the engine isn't getting enough fuel when you open the throttle. Let's walk through it step-by-step. First, you'll want to check t…
-
my stihl ms 250 chainsaw won't start, pulled the cord like 20 times and nothing. what's wrong?
The engine is flooded or the ignition system is blocked. Check three things, in this order. Set the master control lever to the STOP position. Pull t…
-
husqvarna 460 rancher makes a loud knocking or pinging noise when i'm cutting, especially under load. what is that?
Yeah, that knocking is usually pre-ignition or 'detonation,' often caused by bad fuel or an overheated engine. The primary is fuel-related. Drain the…
-
the chain on my husqvarna 455 rancher won't stop spinning when the engine is idling. is this dangerous?
Yes, it's dangerous. The chain should be stationary at idle. The cause is an improperly adjusted idle speed. First action: Let the engine warm up for…
-
is it okay to run regular gas in my husqvarna 460 rancher? what's the right mix?
Yeah, this is a common way to kill a saw. You cannot use regular, unmixed gasoline. This is a 2-cycle engine. The correct fuel is a mix of fresh, hig…
-
my husqvarna 455 rancher chain keeps coming loose and slipping off the bar while i'm cutting. am i doing something wrong?
This usually means the chain tension isn't set correctly or the bar is worn. Here's how to it properly. First, stop the engine and make sure it's coo…
-
stihl ms 250 runs fine then suddenly bogs down and dies in cold weather, like below freezing.
This is carburetor icing. Moisture in the intake air freezes on the carburetor throttle plate, blocking fuel flow. The MS 250 has a winter operation …
-
my stihl ms 250 guide bar is wearing out really fast on one side, what gives?
One-sided wear is caused by not rotating the bar and improper chain sharpening. The is simple and preventative. Every time you sharpen the chain, and…
-
stihl ms 250 chain oil tank is leaking, seems like it's coming from the cap. how do i seal it?
Leaks from the oil tank cap are usually due to a dirty seal, a cross-threaded cap, or a damaged O-ring. First, clean the area thoroughly. Wipe down t…
-
can i use my stihl ms 250 to cut up an old pressure-treated fence post?
No. The machine is designed only to saw wood and wooden objects. Using it on pressure-treated lumber, which contains metals and chemicals, violates t…
-
stihl ms 250 chain won't stop spinning when the engine is at idle, is this dangerous?
Yes. This indicates an incorrectly set idle speed. The chain must not rotate at idle. The cause is a carburetor idle adjustment that is set too high.…
-
my stihl ms 250 is smoking a lot and seems to run hot, is this normal?
No, that is not normal. A Stihl MS 250 smoking excessively and running hot typically indicates an airflow or cooling problem. The first and most like…
-
stihl ms 250 chain keeps coming loose while i'm cutting, how do i fix this?
The chain is stretching as it heats up. You're not maintaining proper tension at operating temperature. Chain tension must be checked and adjusted fr…
-
my stihl ms 250 chainsaw won't start when it's cold, what am i doing wrong?
The primary cause of a cold-start failure on the STIHL MS 250 is typically "flooding" the engine or failing to properly engage the choke sequence. Wh…
-
the chain brake on my husqvarna 455 rancher feels sticky and doesn't always snap on when i need it. how do i service it?
A sticky chain brake is a critical safety failure. The inertia-activated mechanism must work freely. Clean it thoroughly. Sawdust and grime gum up th…
-
my husqvarna 460 rancher is vibrating way more than it used to, feels harsh in my hands. what should i check?
Excessive vibration is hard on you and the saw. The Husqvarna has a LowVib anti-vibration system, so something might be loose or worn. First, check a…
-
can i use a 24 inch bar on my husqvarna 460 rancher that came with a 20 inch? saw seems powerful enough.
The Husqvarna Rancher 460 is engineered with a 60.3cc X-Torq engine that possesses the torque necessary to pull a 24-inch bar, but the primary issue …
-
how do i clean the air filter on my husqvarna 455 rancher? it's running rough and i think it's clogged.
A clogged air filter causes poor performance. Clean it as follows. Remove the air filter cover. Typically, this involves loosening one or two knobs o…
-
husqvarna 460 rancher chain keeps coming loose while i'm cutting, i tighten it and it just happens again. how do i fix this?
This usually means the bar nuts aren't tight enough, or the chain tensioning system needs adjustment. Here's what you do. First, make sure the saw is…
-
my husqvarna 455 rancher won't start at all, not even a sputter. i just gassed it up. what gives?
The total absence of a sputter on a Husqvarna 455 Rancher after a fresh fueling usually indicates one of two things: a complete lack of spark or a "f…