All questions — page 170
Browse by Problem
-
the display is totally blank, no lights, nothing when i plug it in. it’s dead.
This usually points to a power supply issue, not a dead appliance. The connection at the wall, the cord, or the outlet in the pot itself is the first place to …
-
it's making a loud hissing noise and steam is shooting out from around the lid, not the steam release valve.
Steam escaping from the lid seal means your sealing ring isn't doing its job. It's either dirty, damaged, or not seated correctly in its channel. 1) Turn the c…
-
i get the ‘Lid’ error message and it won't start no matter what i do.
The "Lid" error message on the Instant Pot Pro 10-in-1 (6QT) is a safety lockout triggered when the internal sensors detect that the lid is not fully locked in…
-
the lid on my instant pot pro won't turn to lock or unlock, it feels completely stuck.
The floating valve (that little silver pin in the lid) is likely jammed in the 'up' or sealed position because some food gunk got inside, or the silicone seal …
-
my instant pot pro just says ‘food burn’ and shuts off every time i try to pressure cook, even with plenty of liquid.
That's the safety sensor kicking in because it detects something thick or starchy scorching on the bottom of the inner pot, interrupting the heating cycle. It'…
-
my foodi won't let me select the pressure cook setting, the button just doesn't respond. other modes work.
The control panel is locked out of pressure mode because it doesn't detect a safe condition. The lid is either not closed fully, not locked, or the float valve…
-
the air fryer lid fan runs but no heat comes out, food stays cold. is the heater broken?
The Ninja Foodi OL701 utilizes a dual-system architecture where the pressure cooking base and the air frying lid operate on separate circuits. When the fan spi…
-
how do you clean the condensation cup on the back? mine is gross and seems stuck on there.
The condensation cup (drip collector) slides into a recess. It gets stuck when food debris and grease harden, acting like glue. Unplug the cooker and let it co…
-
i get a burn warning every time i try to pressure cook rice, even with plenty of water. what am i doing wrong?
The "Burn" message triggers when the bottom sensor overheats, meaning food is sticking and scorching before pressure builds. Rice and thick sauces are common c…
-
the display on my ol701 is completely dead, no lights, but the power cord is plugged in. is it fried?
A completely dead display on the Ninja Foodi OL701 usually indicates a total break in the electrical circuit before the power reaches the logic board. This is …
-
why does my foodi make a loud clicking noise from the bottom when it's trying to pressurize?
That's the internal pressure switch (a magnetic relay) cycling on and off rapidly. It's trying to maintain temperature. Excessive clicking usually means insuff…
-
just got my ninja foodi ol701 and it won't pressurize, steam just leaks out the side of the lid constantly.
When the Ninja Foodi OL701 fails to pressurize and steam escapes from the perimeter of the lid, the root cause is a failure to create a hermetic seal between t…
-
my ninja foodi pressure cooker keeps showing a C1 error and won't do anything, what does that mean?
The C1 error is a communication fault between the main control board and the pressure lid sensor. It means the cooker can't read if the lid is properly sealed …
-
the keep warm function on my duo nova seems too hot and burns the bottom of my food.
The Keep Warm function maintains a temperature between 145°F and 172°F. For foods with low liquid content (e.g., thick stews, chili), this can cause scorching …
-
water keeps leaking from the steam release valve during cooking, even though it's set to sealing.
Continuous water leakage from the steam release valve stem indicates the valve is not fully seated in the 'Sealing' position, or food debris is blocking the va…
-
i get the C6 or C7 error when trying to make yogurt in my duo nova. what does that mean?
The C6 or C7 error is a temperature sensor fault during the Yogurt program. The pot cannot reach or maintain the precise low temperature required for fermentat…
-
my instant pot won't turn on at all, no lights, nothing. it's plugged into a working outlet.
Complete power failure indicates an issue with the power cord connection, the internal fuse, or a fault in the main control board. No display means no power is…
-
the sealing ring on my duo nova smells terrible, like old food, no matter how much i wash it.
The silicone sealing ring is porous and absorbs food odors, especially from pungent ingredients like curry, garlic, or seafood. Standard washing does not remov…
-
why is my instant pot so loud when it's coming up to pressure? sounds like a hard boil.
Rapid, loud bubbling or a 'hard boil' sound is normal during the initial heating phase. This is water boiling vigorously before enough steam is generated to cl…
-
instant pot duo nova keeps blinking '6' or 'L6' and won't do anything when i press a button
The L6 or 6 error is a communication fault between the main unit and the lid. The lid sensor cannot confirm the lid is properly closed. 1. Unplug the base for …
-
my instant pot duo nova just says 'burn' and won't start pressurizing, what am i doing wrong?
The Burn error (BURN or bURN) triggers. This indicates insufficient liquid or food scorched to the bottom during preheating, preventing pressure build-up. 1. P…
-
how do you clean this thing? it's packed with sawdust and i'm worried about breaking it.
The DeWalt DCS354B is a high-vibration tool, which means sawdust doesn't just sit on the surface; it migrates into the internal housing via the cooling vents a…
-
my dewalt oscillating tool won't turn on at all, battery is charged and works in other tools.
The complete failure of a DeWalt DCS354B to power on, despite a known-good battery, typically points to a failure in the electrical continuity path between the…
-
the tool head on my dcs354b has a lot of side-to-side wiggle or play, is that normal?
While a microscopic amount of movement is inherent to the oscillating design of the DeWalt DCS354B, any "wiggle" that is visible to the naked eye or causes the…
-
dewalt 20v multitool feels weak, bogs down immediately even with a fresh battery on simple cuts.
The "bogging down" sensation in the DeWalt DCS354B is rarely a failure of the brushless motor itself, but rather a failure of energy transfer between the tool'…
-
blade keeps falling off my dewalt oscillating tool even when i tighten the bolt, it's driving me nuts.
The DCS354B utilizes a tool-less quick-change system that relies on a clamping bolt and a keyed oscillating plate. When blades slip despite the bolt being tigh…
-
the speed dial on my dewalt multi-tool does nothing, it's stuck on one speed.
The DeWalt DCS354B uses a potentiometer—a variable resistor—to control the motor speed. Because this tool is frequently used for sanding and drywall cutting, m…
-
dewalt dcs354b makes a horrible grinding or rattling noise when i turn it on, not the normal vibration.
The grinding or rattling noise in the DeWalt DCS354B is typically caused by the failure of the eccentric drive assembly or the loosening of the drive spindle. …
-
my dewalt oscillating tool just stopped running mid-cut, battery is fine, what gives?
The DeWalt DCS354B is equipped with an internal thermal overload protection circuit designed to prevent the motor windings from melting or shorting during high…
-
after not using it for a few months, my v20 drill won't turn on even with a battery i know is good, totally dead.
The total loss of power in a Craftsman V20 CMCD700C1 after prolonged storage is typically caused by one of two things: surface oxidation on the battery contact…
-
craftsman v20 drill makes a high-pitched whining or grinding noise in speed setting 2, is the gearbox shot?
The high-pitched whining or grinding noise specifically occurring in speed setting 2 (high speed) on the Craftsman V20 CMCD700C1 indicates a failure in the pla…
-
my drill works fine but the led worklight doesn't come on anymore, can i replace just the light?
The Craftsman V20 CMCD700C1 utilizes a low-voltage LED integrated into the base of the gear housing. Because LEDs are semiconductor devices with incredibly lon…
-
the chuck on my cmcd700c1 wobbles slightly when i run the drill, is the chuck broken or can i tighten it?
The wobble you are experiencing in your Craftsman V20 CMCD700C1 is typically caused by one of two things: a loose chuck retaining screw or a misalignment of th…
-
why does my craftsman drill slow down and sound strained when i put any pressure on it, even with a fresh battery?
The "straining" sound and sudden drop in RPMs on the Craftsman V20 CMCD700C1 are typically caused by one of two things: an incorrect torque clutch setting or a…
-
v20 drill battery won't click into the drill solidly, it just falls out if i tilt it, how do i fix the latch?
The failure of the battery to lock into the Craftsman V20 CMCD700C1 is typically caused by a failure in the mechanical engagement between the drill's release t…
-
craftsman cmcd700c1 drill gets super hot in the handle after like 5 minutes of use, is that normal?
No, it is not normal for the handle of the Craftsman V20 CMCD700C1 to become "super hot" within five minutes of use. While a slight warmth in the motor housing…
-
my craftsman v20 drill just clicks but the chuck doesn't spin at all, battery is charged, what's wrong?
The "clicking" sound you hear when pulling the trigger on your Craftsman V20 CMCD700C1 is the sound of the electronic variable speed switch engaging the relay,…
-
the led work light on the front of my saw won't turn on anymore
The Ryobi ONE+ 18V Reciprocating Saw P519 is designed for high-vibration demolition work, which is the primary enemy of the LED work light circuitry. Because t…
-
there's a bad burning smell coming from my saw near the motor, and sometimes a little smoke
The burning smell and smoke emanating from the motor housing of your Ryobi ONE+ 18V Reciprocating Saw (P519) indicate that the armature windings or the carbon …
-
i can't get the variable speed to work on my p519, it's only full blast or nothing
The Ryobi P519 uses a variable-speed trigger assembly that relies on a potentiometric contact system to modulate the voltage sent to the motor. When you experi…