Routers & Mesh Systems (Page 3)
-
the clear plastic sub-base is cracked and now it vibrates like crazy, where do i even get a new one?
The vibration you are experiencing is caused by a loss of structural integrity in the polycarbonate sub-base. On the Ryobi ONE+ HP Compact Router (PS…
-
why is my ryobi compact router making a high-pitched whining noise and slowing down under light load?
The high-pitched whining noise combined with a loss of torque under light load in the Ryobi ONE+ HP Compact Router (PSBCR01B) is a classic symptom of…
-
router bit keeps slipping down while i'm using it, can't get it to stay locked at the right depth.
The slipping issue on the Ryobi ONE+ HP Compact Router (PSBCR01B) is almost always caused by a failure in the mechanical interface between the depth …
-
my ryobi one+ hp compact router suddenly has no power, won't turn on with a fresh battery.
The battery is likely not making proper contact with the router's terminals. This model has a known issue with the battery latch mechanism. Remove th…
-
the 2.4ghz network from my be800 keeps dropping for my smart plugs and lights, but the 5ghz is fine.
Many smart home devices have weak Wi-Fi antennas and are sensitive to interference. The BE800's powerful radio might also be causing issues if it's s…
-
trying to set up the be800 with the tether app and it just won't find the router during setup, it's stuck on searching.
The app can't establish an initial connection. This is usually because your phone isn't connected to the router's default setup network, or there's a…
-
my wifi speed on the be800 is way slower than i expected, like not even close to my old router sometimes.
This is almost always a device or configuration issue, not the router being slow. Common culprits are older client devices, incorrect band selection,…
-
how do i actually turn off those crazy bright rgb lights on the front? they're lighting up my whole room at night.
The BE800 has a customizable LED matrix that's pretty bright by default. It's designed to show status, but you have full control to dim or disable it…
-
the internet light on my be800 is red and i have no connection, but my modem is fine.
A red Internet LED means the router cannot establish a connection to your modem or to your Internet Service Provider (ISP). The physical link is like…
-
why does my archer be800 make a faint but annoying high-pitched whining or buzzing sound?
That's coil whine. It's coming from the internal power circuitry or transformers and is a common, albeit annoying, phenomenon in electronics with hig…
-
just got this wifi 7 router but my older laptop and phone can't even see the network, is it broken?
It's not broken. The BE800's default settings often enable the new 6 GHz band (Wi-Fi 7) and a 'Smart Connect' feature that can confuse older devices …
-
my new be800 router just has a solid amber light on the front and won’t give out any wifi, what do i do?
A solid amber status light means the router is powered on but failed its startup sequence. It's likely stuck in a boot loop or corrupted its firmware…
-
after the latest firmware update, my alien's 5ghz wifi just disappeared and all my devices are stuck on 2.4.
A bad firmware update can sometimes corrupt the wireless driver or reset a band-specific setting. The 5GHz radio is probably disabled or stuck. Let's…
-
the wifi signal from my alien mesh point is really weak, way worse than the main router even in the same room.
This usually means the mesh point has a poor wireless 'backhaul' connection to the main router. It's struggling to talk to the base, so it has nothin…
-
upgraded to gigabit internet but my alien router speed tests on the app never go above 500-600 mbps wired.
You're likely hitting a limit of the built-in speed test server or there's a configuration bottleneck. The Alien's hardware can handle gigabit, but y…
-
i keep getting 'device isolation alert' on my phone from the amplifi app and some gadgets can't talk to each other.
That alert means 'Client Isolation' or 'AP Isolation' is turned on. It's a security feature that prevents devices on your WiFi from seeing each other…
-
my internet is fine but the alien's light ring stays solid red all the time and won't turn blue.
A solid red light means the Alien router itself has no internet connection from your modem. Your devices might still be working on the local network,…
-
the touchscreen on my alien router is completely unresponsive, i can't swipe or tap anything.
The touchscreen has likely frozen, which is a software glitch, not a broken screen. A simple reboot often fixes it. Let's do a soft reboot first. 1) …
-
just got an alien mesh point and it won't pair to my main router, the light just flashes white forever.
The mesh point is stuck in its pairing mode and can't find the main router's signal. This usually happens if they're too far apart during setup or if…
-
my amplifi alien keeps rebooting on its own every couple hours, the light ring just goes out and then starts back up.
This is almost always a power issue. The Alien's power supply is a known weak point and can get flaky, especially if it's been warm or you're using a…
-
after a power outage, my atlas max nodes are all on but the wifi network name is gone and i can't connect.
The router's settings have likely been corrupted or reset to a default state. This can happen if the power flickers during a write cycle to the inter…
-
the parental controls or device pause in the linksys app just stopped working, the timers don't cut off the internet.
When a device is paused or on a schedule but still has internet access, it almost always means that device has switched to using cellular data (on a …
-
my device keeps disconnecting from the wifi or switching to a weak node even when i'm right next to a stronger one.
This is usually "client steering" or "roaming" not working perfectly. Your device (laptop, phone) is being stubborn and holding onto the first node i…
-
how do i port forward on the atlas max 6e? i can't find the setting anywhere in the app.
The Linksys app simplifies a lot of advanced settings. For port forwarding, you need to use the traditional router web interface, which the app doesn…
-
one of my atlas max nodes is making a faint but annoying high-pitched whining or buzzing sound, is it broken?
That's coil whine. It's not a sign of a defect that will cause a failure, but it's an annoying acoustic artifact from electrical components (like ind…
-
why is my wifi speed so much slower than my internet plan on the atlas max 6e, especially on my phone?
Your device (like a phone) is probably connecting to the 2.4 GHz band for a more stable signal, which is much slower, instead of the faster 5 GHz or …
-
setting up my new atlas max 6e and the app just keeps saying 'unable to connect to the internet' even though my modem works fine
This is almost always a classic "order of operations" issue during setup. The router is likely trying to pull an IP address from your modem before th…
-
my linksys atlas max 6e router just has a solid red light on one of the nodes and my wifi is gone, what do i do?
That solid red light means the node has lost its connection to the main router or the mesh network. It's essentially stranded and can't talk to the r…
-
my gaming pc wired into the axe75 gets lag spikes even though the internet is fine on other devices.
This points to a problem specific to that Ethernet port or the traffic management settings affecting that wired connection. It could be a faulty cabl…
-
i factory reset my axe75 and now it's creating a wifi network called 'TP-Link_XXXX' but i can't set it up, the app won't find it.
After a factory reset, the router broadcasts a default open network to facilitate initial setup. The TP-Link Tether app can sometimes fail to discove…
-
the led lights on my axe75 are way too bright for my bedroom, can i turn them off completely?
You can't dim them, but you can turn the front panel indicator LEDs off entirely through the router's software. There's no physical button for it on …
-
the internet speed on my wifi 6e devices is way slower than my old router, even right next to the axe75.
The router's hardware is capable, so this is almost always a configuration or device negotiation issue. Common culprits are band steering pushing dev…
-
i can't access tplinkwifi.net or 192.168.1.1 to get into my axe75 settings anymore.
Your computer or phone is no longer on the same network segment as the router's management interface. This usually happens if you've changed the rout…
-
my axe75 router randomly reboots itself every day or two, it's driving me nuts.
Yeah, this one's common. An Archer AXE75 rebooting on its own is almost always a heat or power supply issue. These routers put out a lot of wireless …
-
the 6ghz band on my axe75 just vanished from the list of networks on my phone, i can't see it anymore.
Your phone or device likely lost the connection because the router's 6 GHz band (Wi-Fi 6E) is either disabled or its settings were changed. The 6 GHz…
-
my archer axe75 keeps blinking orange on the internet light and won't get online, i've rebooted a bunch of times.
The router can't establish a connection to your modem or ISP. The blinking orange Internet LED specifically indicates a WAN (Wide Area Network) link …
-
trying to set up aimesh with another asus node but the ax86u pro won't find it, the search just times out.
The nodes are likely on different firmware versions, or you're trying to use an incompatible older router as a node. Update both devices to the exact…
-
my internet speed through the router is half what i get directly connected to the modem, even on ethernet.
QoS (Quality of Service) or traffic monitoring features are enabled and throttling your connection. They cap maximum throughput. Disable all QoS and …
-
the guest network on my ax86u pro just disappears after a few hours, have to reboot to get it back.
This is a known firmware bug related to the guest network scheduler or a conflict with other features like VPN. Disable the guest network access time…
-
i keep getting 'your connection is not private' errors on some devices after setting up this router.
The router's time is incorrect, which breaks SSL/TLS certificates for websites. This happens if it can't sync with an NTP time server at boot. Manual…
-
my asus router's fans are loud and spin up constantly, it sounds like a laptop under load, is this normal?
The RT-AX86U Pro has an internal fan that kicks in under high CPU load (like VPN processing, heavy traffic). Constant loud noise suggests it's stuck …
-
the 2.4ghz wifi on my ax86u pro is super slow, like 20 mbps when i pay for 500, but 5ghz is fast.
The 2.4GHz band is congested or stuck in a legacy compatibility mode (like 802.11b/g). This crushes speed. Force the 2.4GHz band into modern, faster …
-
just got this router and the internet light is solid red, no connection even though my modem is fine.
The WAN (Internet) port isn't getting a valid IP address from your modem. This is almost always a handshake or cable issue. Power cycle the entire ch…
-
my new asus rt-ax86u pro keeps dropping the 5ghz wifi signal randomly, but the 2.4ghz is fine, what gives?
You're experiencing interference or a channel conflict on the 5GHz band. It's a common setup issue, not hardware failure. Log into the router's web i…
-
the orbi app says my firmware update failed and now my system is acting weird.
A failed or interrupted firmware update can leave the system in a partially updated, unstable state. This causes odd behavior like random reboots, se…
-
how do i factory reset this thing? i lost the admin password and the app won't let me in.
You're locked out. A factory reset wipes all settings, including your custom password, and returns everything to the default credentials printed on t…
-
the internet speed from my satellite is way slower than from the main router, like half or less.
This is almost always a backhaul problem. The satellite talks to the router wirelessly, and if that connection is weak or on a crowded channel, your …
-
after a power outage, my orbi router has a solid amber light and no internet.
A solid amber light on the router means it's powered on but can't establish an internet connection from your modem. The power outage likely caused a …
-
i can't get the 6ghz band to show up on my new samsung phone even though it supports wifi 6e.
The 6GHz band is often hidden by default or has separate settings. Your phone might also be defaulting to an older band for compatibility. The most c…
-
the satellite keeps making a faint clicking or buzzing noise, it's not loud but it's in my bedroom and it's annoying.
That's coil whine—a high-frequency buzzing or clicking from the internal power electronics. It's not dangerous, but it can be audible in a quiet room…