All questions — page 51
Browse by Problem
-
garage door opener makes a loud grinding or screeching noise only when going up. it's a legacy 920.
When an Overhead Door Legacy 920 makes a loud grinding or screeching noise exclusively during the ascent, it indicates a failure of the drive system to maintai…
-
my legacy 920 opener just beeps three times at me and won't move the door. what does that mean?
The three-beep sequence on an Overhead Door Legacy 920 Belt Drive is a specific diagnostic code indicating a "Travel Limit" or "Obstruction" error. Essentially…
-
the air quality light stays red even after running on turbo for an hour in a small room.
The Medify MA-40 V2.0 utilizes an infrared laser particle sensor located on the rear of the chassis to monitor PM2.5 levels. When the indicator light remains r…
-
the replacement hepa filter i bought doesn't fit snugly, it wobbles inside the unit.
The instability and wobbling of the filter in your Medify MA-40 V2.0 is almost certainly caused by a dimensional mismatch between the filter frame and the inte…
-
my purifier turns off by itself after a few hours on timer mode, but i didn't set a timer.
The Medify MA-40 V2.0 is experiencing an automatic power-down sequence caused by the activation of the "Child Lock" safety mode. While this feature is primaril…
-
how do i clean the outside of this thing? the white plastic has grey smudges that won't come off.
The Medify MA-40 V2.0 utilizes a high-impact, matte-finish ABS plastic for its exterior housing. The grey smudges you are seeing are typically not "dirt" in th…
-
the auto mode light is on but the fan doesn't seem to speed up even when i spray air freshener nearby.
The Medify MA-40 V2.0 utilizes a laser-based particle sensor to trigger its Auto Mode. When the "Auto" indicator is lit, the onboard logic is waiting for a spe…
-
i just got my ma-40 and the touch controls don't respond at all, it's just a black screen.
The lack of response from the Medify MA-40 V2.0 touch panel, characterized by a completely black screen and unresponsive buttons, is typically caused by the un…
-
why is my air purifier making a loud rattling or buzzing noise on the highest fan speed?
The loud rattling or buzzing noise experienced at the highest fan speed (Speed 4/Turbo) on the Medify MA-40 V2.0 is typically caused by mechanical resonance. A…
-
my medify ma-40 just shows a red 'filter' light after a few months, isn't it supposed to last longer?
The red "Filter" indicator on the Medify MA-40 V2.0 is not triggered by an actual air quality sensor or a pressure differential switch that measures how "clogg…
-
the electronic light on my pur faucet filter just doesn't come on at all, even with a new battery.
The PUR PFM400H electronic monitor is a standalone timer circuit powered by a single CR2 lithium battery. When the LED fails to illuminate despite a fresh batt…
-
no water comes out on the filtered setting, but unfiltered works fine from my faucet.
The PUR PFM400H is a diverter-style system that relies on a mechanical slide valve to redirect water from the main faucet stream into the filter housing. When …
-
the pur filter won't snap into the housing, it just spins and doesn't lock, even though it's the right model.
The failure of a PUR PFM400H filter to lock into the housing is typically caused by a mechanical obstruction or a misalignment of the bayonet-style locking lug…
-
the filter handle is super stiff and hard to switch from filtered to unfiltered water on my pur faucet mount.
The stiffness in the PUR PFM400H diverter handle is almost always caused by the accumulation of calcium carbonate and magnesium deposits, commonly known as lim…
-
my water tastes weird or kinda plastic-y even with the new pur faucet filter, did i get a bad one?
The "plastic" or chemical taste you are experiencing with your PUR PFM400H is rarely a sign of a defective unit. Instead, it is almost always caused by "carbon…
-
the filter light on my pur faucet mount is flashing red and blue alternately, what does that mean?
The alternating red and blue flashing light on the PUR PFM400H is a specific status notification indicating that the filter cartridge has reached its maximum r…
-
water is leaking from where the pur filter connects to my faucet, it drips down the side of the base.
The leak occurring at the connection point of the PUR PFM400H is typically caused by a failure in the seal between the faucet's diverter valve stem and the fil…
-
my pur faucet filter light is solid red and the water stream is really slow, just installed a new filter too.
The solid red light on your PUR PFM400H indicates a "Filter Replacement Required" status. If you have already installed a new cartridge, the light remains red …
-
clothes come out of this dryer still really wet in one spot, like a damp stripe. it's not overloaded.
Poor tumbling. The lifters (the baffles inside the drum) are worn smooth or broken, or you're overloading with heavy items like blankets that just roll instead…
-
the interior light stays on all the time even when the dryer door is closed, is that normal?
No, it's not normal. The door switch is stuck in the 'depressed' position or has failed internally in the closed state. The switch has two functions: telling t…
-
my dryer stops mid-cycle and just hums like the motor is trying to run but the drum won't turn.
A seized idler pulley or a broken drive belt. The motor hums because it's engaged but can't turn the obstructed drum. Unplug the dryer. Access the drum area by…
-
the start button on my amana dryer doesn't do anything when i press it, no lights, no nothing. it's plugged in.
No power to the control board. This is usually a blown thermal fuse or a failed door switch, not the start button itself. Check the thermal fuse first. It's a …
-
there's a loud thumping or scraping noise when the dryer runs, sounds like it's coming from the back.
A worn out drum support roller or a foreign object (like a coin or bra wire) caught between the drum and the rear bulkhead. Unplug the dryer. Remove the front …
-
the drum in my amana dryer spins but there's no heat at all, clothes just stay cold and damp.
A failed heating element, thermal fuse, or high-limit thermostat. On electric dryers, these are the usual suspects for a 'no heat' condition. Unplug the dryer.…
-
my ned4655ew dryer heats up but takes forever to dry even a small load, like two hours. lint filter is clean.
Restricted airflow. The most common culprit is a clogged vent hose or external duct, not the internal lint filter. Disconnect the flexible vent hose from the b…
-
my amana dryer just beeps three times and the door light flashes, it won't start at all, what's wrong?
The control board is detecting the door isn't fully latched. The door switch or latch mechanism is likely faulty or misaligned. First, check the physical latch…
-
the fan on my cinebeam is crazy loud all of a sudden, like it's running at full speed even when the picture is dark.
The projector's internal temperature sensor thinks it's overheating, so it's commanding the cooling fan to run at maximum RPM to try to save the laser and elec…
-
i see a weird dark shadow or blurry spot in the corner of the image from my lg projector. it doesn't go away.
That's likely a piece of dust or debris that has settled on the internal lens or, more seriously, on the surface of the DLP chip inside the sealed optical engi…
-
the built-in smart apps (like netflix) are super slow and keep freezing on my pu700r. my wifi is fine.
This is a common gripe with built-in projector smart platforms. They often have underpowered processors and not much memory compared to a dedicated streaming s…
-
the auto keystone on my lg cinebeam keeps making the picture a trapezoid instead of fixing it. it's driving me nuts.
The auto keystone correction is getting confused, usually because it's trying to correct for a surface that isn't a flat, white screen, or because the projecto…
-
my projector says 'no signal' but everything is plugged in. using hdmi from my fire tv stick.
This is almost always a handshake issue between the projector and your source device. They're not agreeing on a video signal format when they first connect. Le…
-
how do you clean the filter on the lg cinebeam? i can't find it and the manual is useless.
You're right to look for it—keeping the filter clean is crucial for cooling. On the PU700R, the air filter isn't a user-serviceable part you can pull out and r…
-
lg pu700r making a high-pitched whining or buzzing noise, seems to be coming from the lens area. is this normal?
You're likely hearing the laser diode driver or the color wheel spinning at high speed. A faint, steady whir is normal, but a pronounced, high-pitched buzz or …
-
my new lg cinebeam pu700r won't turn on at all, the power button light just blinks red a few times and then nothing.
The projector is failing its internal power-on self-test. A blinking red light is its way of telling you something's not right before it even tries to fire up …
-
one side of my desk goes up faster than the other, it's not level at all during movement.
The two motor columns are out of synchronization. This is a controller or communication cable issue. Perform a synchronization procedure. Lower the desk to its…
-
i assembled my new SHW desk but it wobbles side to side when i type, even at the lowest height.
The crossbar is not tightened enough. This is the metal brace that connects the two legs under the desk. It is the primary source of lateral stability. Get a h…
-
the control box under my SHW desk gets really hot to the touch, is that normal?
The control box on an SHW Electric Height Adjustable Standing Desk acts as the brain and power regulator for the dual-motor system. While it is normal for the …
-
the desk won't go all the way down to the lowest setting anymore, stops about 2 inches high.
The SHW Electric Height Adjustable Standing Desk utilizes a digital encoder system within the lifting columns to track the exact position of the motor. When th…
-
how do you clean the white top on these SHW desks without ruining it? the laminate is getting stains.
The white surface of the SHW Electric Height Adjustable Standing Desk is composed of a melamine-infused laminate over a particle board core. While this materia…
-
my desk makes a loud grinding noise on one side when going up, the other side is fine.
One of the two lift columns is failing. The grinding is metal-on-metal wear inside the telescoping leg, likely from a damaged gear or lack of grease. Stop usin…