All questions — page 52
Browse by Problem
-
the memory presets on my SHW desk stopped working, it just goes to random heights now.
The desk's control unit has lost its saved settings. A brief power interruption or a voltage spike can cause this. You need to reprogram the controller. Unplug…
-
my SHW standing desk just beeps three times and won't go up or down, what's the deal?
The desk's controller is getting conflicting signals from its safety sensors. This is almost always the anti-collision system triggering. Clear the obstruction…
-
the deck and handlebars got really dirty, can i just wipe it down with a wet towel or what?
The deck is vulcanized rubber and the handles are silicone. Both can be cleaned, but moisture must be kept away from electronic junctions. Use a cloth dampened…
-
the charger light stays green even when i first plug it into the dead scooter, it's not charging.
This indicates no communication between the charger and the scooter's battery management system (BMS). The circuit is open. Unplug the charger from the wall an…
-
the folding mechanism is super stiff and i'm scared i'm gonna break it trying to lock it.
The stainless steel latch pins and the receiver holes are likely dry or have accumulated fine dust/debris, increasing friction. Fold the scooter to the unlocke…
-
my scooter suddenly brakes by itself for a second or feels like it's surging, not smooth.
This is the electronic regenerative braking system engaging inconsistently, often due to a faulty throttle sensor or connection. Power the scooter off. Visuall…
-
the range on my e500 is way less than advertised, like 5 miles on a full charge in mode 2.
This is typically due to a combination of rider weight, terrain, and tire pressure. The advertised range is under ideal lab conditions. Check and adjust tire p…
-
how do i pair my unagi with the app? it never shows up in my phone's bluetooth list.
The scooter's Bluetooth module is not in discovery mode. It only broadcasts its signal under specific conditions. First, turn the scooter on. The power light m…
-
the scooter makes a loud clicking or grinding noise from the front wheel when i accelerate, feels rough.
This is almost always a foreign object lodged in the gear drive of the front motor. The Model One uses a geared hub motor, not direct drive. Turn the scooter o…
-
my unagi e500 just beeps twice and won't turn on, the power button lights up red for a second then nothing.
This is the low battery protection circuit activating. The battery voltage is below the safe operating threshold for the BMS. Connect the official Unagi charge…
-
the night vision is really grainy and the image is almost black and white with weird green tints, is my camera defective?
Probably not defective. That's the characteristic of the infrared (IR) night vision this and most monitors use. It's inherently monochrome (black and white/ gr…
-
i'm getting a 'cannot connect to server' error in the app and can't see the live stream, everything else on my phone has internet
This is almost always a problem on Cubo's cloud server end, not your local Wi-Fi. Their servers occasionally have outages or maintenance periods that break the…
-
the camera gets really hot to the touch, especially near the top, is that normal or a fire hazard?
It's normal for the Cubo Ai Plus to feel warm, even notably hot, during operation. The heat comes from the processor running the AI analytics, the Wi-Fi radio,…
-
the rollover detection alert never goes off, even when we test it with a doll, is it broken?
The rollover detection is the most finicky feature because it relies on a specific IR sensor array (not just the camera) and very precise setup. It's often not…
-
the cry detection isn't working at all, or it goes off for random noises like the humidifier
The sound detection needs tuning. It's either not sensitive enough for your baby's specific cry, or it's too sensitive and picking up ambient white noise as a …
-
how do you clean the cubo ai plus camera? the manual says not to use liquids but it gets dusty and has fingerprints
You're right to be cautious. The front has a camera lens, a microphone port, and the important IR sensor for the rollover detection. Harsh cleaners can haze th…
-
the camera says 'face covered' alert constantly even when there's nothing near the baby's face, it's driving us nuts
Yeah, this one's common. The AI's face detection algorithm is getting triggered by high-contrast patterns on the crib bedding, like dark seams on light sheets,…
-
my cubo ai plus camera keeps going offline and i have to unplug it to get it back, happening like every other day
This is usually a Wi-Fi handshake issue. The camera's connection to your router is dropping and it can't re-establish on its own without a full power cycle. Fi…
-
the auto shut off isn't working, i left it on by accident and it was still scorching hot hours later.
The internal timer circuit responsible for the automatic shut-off mechanism has failed. In the Hot Tools Pro Artist 24K Gold series, this safety feature is des…
-
the swivel cord on my hot tools iron is getting really stiff and tangled, it's annoying to use.
The stiffness and tangling in the Hot Tools Pro Artist 24K Gold Curling Iron swivel cord are caused by "torsional stress" and heat-induced degradation of the P…
-
my iron seems way hotter than the dial setting, it's smoking and burning my hair even on low.
The internal thermostat, a crucial safety component that regulates temperature, has failed. It is likely stuck in the "on" position, causing the heating elemen…
-
the temperature dial feels loose and spins without clicking, and the heat seems inconsistent now.
The issue is caused by the failure of the internal spring-loaded detent ball or the plastic indexing gear located behind the temperature control dial. In the H…
-
how do i clean the gunk off the gold barrel without ruining the finish?
Product buildup (hairspray, serum, conditioner) is baked onto the barrel's surface, reducing its non-stick properties and transfering residue to your hair. The…
-
the clamp on my curling iron is super loose and won't hold the hair, it just slips out.
The loose clamp on the Hot Tools Pro Artist 24K Gold Curling Iron is typically caused by a failure in the tensioning spring or a loosening of the pivot pin tha…
-
my pro artist iron won't heat up past barely warm, the light is on but it's not getting hot.
When the Hot Tools Pro Artist 24K Gold Curling Iron shows a powered-on indicator light but fails to reach operational temperature, you are dealing with a parti…
-
my hot tools 24k curling iron's gold coating is flaking off near the clamp, is it ruined?
The 24k gold-plated barrel is degrading from heat stress and mechanical wear at the high-friction clamp contact point. This is a common cosmetic issue. Stop us…
-
it won’t hold a charge for more than a couple brushes now, used to last weeks
The rechargeable lithium-ion battery is degrading. This is normal wear and tear after a couple of years of daily use and charge cycles. Before declaring the ba…
-
the different modes don’t feel any different, it’s just the same intensity on all settings
The mode selection button or the control circuit might be stuck, or the brush is defaulting to its primary cleaning mode due to a glitch. First, let's rule out…
-
how do i clean the gunk out of the little hole where the brush head goes? it’s gross
That's the drive shaft socket, and it's a magnet for toothpaste slurry and saliva, which hardens into a cement-like gunk. Unplug the base. You'll need a toothp…
-
it’s way too loud and vibrates really rough now, didn’t used to be like this
This is a classic sign of a worn-out or unbalanced brush head. The internal motor is fine, but the attachment is causing the violent shaking. First, try a bran…
-
the charging light on my aquasonic base just stays solid red, never turns green even after all night
The battery isn't taking a charge. This can happen if the battery has been deeply discharged (left dead for months) or has reached the end of its lifespan. Try…
-
my toothbrush turns on by itself in the middle of the night, just starts vibrating on the charger
Water has gotten inside the handle and is causing a short circuit, tricking the power button. This is a common issue if the seal around the button is compromis…
-
the brush head on my aquasonic ultra whitening keeps coming loose and flying off while i’m brushing
The metal shaft that drives the brush head has likely collected a hard ring of old toothpaste and mineral deposits. This prevents the head from snapping on all…
-
my aquasonic black series toothbrush just stopped turning on and it’s fully charged i think
This is almost always a connection issue between the handle and the charging base, not a dead battery. A tiny bit of water or toothpaste residue can break the …
-
i can't get the high-pressure hose to connect to the spray gun, it just leaks.
The quick-connect fitting is not fully seated or the O-ring inside is missing/damaged. First, ensure the hose is for high-pressure (has metal braiding). Push t…
-
the pressure is really weak and pulsates, even with a new tip.
A worn or damaged pump unloader valve. This valve regulates pressure by recirculating water. When it fails, pressure drops and surges. This requires accessing …
-
water is leaking from the bottom of the pump near the connections.
The leaking occurring at the bottom of the CMEPW1900 pump manifold is typically caused by the degradation or displacement of the internal O-rings and seals loc…
-
the soap injector isn't pulling any detergent from the bottle.
The chemical injection system is either not engaged or the filter is blocked. It uses a venturi, not a pump. First, ensure you have selected the 'LOW PRESSURE …
-
it keeps shutting off by itself after a few minutes of use.
The Craftsman CMEPW1900 is equipped with a thermal overload protector designed to kill power to the motor when internal temperatures exceed safe operating limi…
-
the machine makes a loud knocking or rattling noise when it's running.
The loud knocking or rattling noise in your Craftsman CMEPW1900 is a classic symptom of pump cavitation. This occurs when the pump is unable to draw a consiste…