Power Tools (Page 6)
-
my chainsaw makes a high-pitched whining or grinding noise when it runs, doesn't sound right.
The high-pitched whining or grinding noise in the DeWalt DCCS620B is typically caused by one of two mechanical failures: acute friction due to a lubr…
-
the chain on my dccs620b keeps coming loose no matter how tight i get it, i tighten it and two cuts later it's sagging again.
The DCCS620B is a high-torque tool, and the rapid loosening of the chain usually stems from one of three root causes: improper initial tensioning (ov…
-
oil is leaking out of my dewalt chainsaw like crazy from the bottom when it's just sitting in the garage.
The leakage occurring in the DeWalt DCCS620B is typically caused by the gravity-fed design of the bar and chain oiling system. Unlike the motor, whic…
-
chainsaw starts but then stops after a few seconds of cutting, like it's overheating or something. battery is full.
The DeWalt DCCS620B features an integrated Electronic Overload Protection (EOP) system designed to protect the brushless motor from permanent thermal…
-
my dewalt 20v chainsaw ran fine yesterday but today it just clicks when i pull the trigger, no blade movement at all.
The rhythmic "click" you hear when pulling the trigger on the DeWalt DCCS620B is the sound of the motor attempting to engage while the mechanical cha…
-
i just assembled my new ryobi mower and the side discharge chute flap won't stay up, it just flops down.
The issue with your Ryobi RY401018 side discharge flap is caused by the absence of the side discharge retention clip. During the factory assembly and…
-
the blade on my ryobi 40v won't spin by hand even with battery out, feels totally locked up.
The Ryobi RY401018 utilizes a direct-drive brushless motor system where the blade is mounted directly to the motor shaft. When the blade is completel…
-
there's a bad grinding noise from one rear wheel on my ryobi 40v, and it's hard to push.
The grinding noise and increased rolling resistance on the RY401018 are typically caused by a failure in the rear wheel assembly, specifically involv…
-
my ryobi mower battery shows full on the charger but dies in like 5 minutes when i mow.
The issue you are experiencing with your Ryobi 40V 20-inch Brushless Push Mower (RY401018) is known as "voltage sag" or "surface charging." The charg…
-
how do you get this mower to fold for storage? the handle seems stuck and i don't want to break it.
The Ryobi RY401018 utilizes a multi-point pivot system designed for vertical storage, but the handle often feels "stuck" due to mechanical binding. T…
-
the self-propel on my ryobi 40v just stopped working, handle lever feels loose and does nothing.
The loss of resistance in the self-propel bail handle combined with a total failure of the drive system on the Ryobi RY401018 indicates a mechanical …
-
ryobi 40v mower suddenly sounds like a jet engine and cuts really poorly, just scatters grass everywhere.
The "jet engine" sound is a classic symptom of aerodynamic turbulence caused by a massive buildup of organic debris inside the cutting chamber. When …
-
my ryobi 40v mower just beeps three times when i pull the start handle and does nothing, what gives?
The triple-beep sequence on the Ryobi RY401018 is a specific diagnostic code indicating a "Start-up Failure" caused by a break in the electrical circ…
-
how do you clean this thing? it's packed with sawdust and i'm worried about breaking it.
The DeWalt DCS354B is a high-vibration tool, which means sawdust doesn't just sit on the surface; it migrates into the internal housing via the cooli…
-
my dewalt oscillating tool won't turn on at all, battery is charged and works in other tools.
The complete failure of a DeWalt DCS354B to power on, despite a known-good battery, typically points to a failure in the electrical continuity path b…
-
the tool head on my dcs354b has a lot of side-to-side wiggle or play, is that normal?
While a microscopic amount of movement is inherent to the oscillating design of the DeWalt DCS354B, any "wiggle" that is visible to the naked eye or …
-
dewalt 20v multitool feels weak, bogs down immediately even with a fresh battery on simple cuts.
The "bogging down" sensation in the DeWalt DCS354B is rarely a failure of the brushless motor itself, but rather a failure of energy transfer between…
-
blade keeps falling off my dewalt oscillating tool even when i tighten the bolt, it's driving me nuts.
The DCS354B utilizes a tool-less quick-change system that relies on a clamping bolt and a keyed oscillating plate. When blades slip despite the bolt …
-
the speed dial on my dewalt multi-tool does nothing, it's stuck on one speed.
The DeWalt DCS354B uses a potentiometer—a variable resistor—to control the motor speed. Because this tool is frequently used for sanding and drywall …
-
dewalt dcs354b makes a horrible grinding or rattling noise when i turn it on, not the normal vibration.
The grinding or rattling noise in the DeWalt DCS354B is typically caused by the failure of the eccentric drive assembly or the loosening of the drive…
-
my dewalt oscillating tool just stopped running mid-cut, battery is fine, what gives?
The DeWalt DCS354B is equipped with an internal thermal overload protection circuit designed to prevent the motor windings from melting or shorting d…
-
after not using it for a few months, my v20 drill won't turn on even with a battery i know is good, totally dead.
The total loss of power in a Craftsman V20 CMCD700C1 after prolonged storage is typically caused by one of two things: surface oxidation on the batte…
-
craftsman v20 drill makes a high-pitched whining or grinding noise in speed setting 2, is the gearbox shot?
The high-pitched whining or grinding noise specifically occurring in speed setting 2 (high speed) on the Craftsman V20 CMCD700C1 indicates a failure …
-
my drill works fine but the led worklight doesn't come on anymore, can i replace just the light?
The Craftsman V20 CMCD700C1 utilizes a low-voltage LED integrated into the base of the gear housing. Because LEDs are semiconductor devices with incr…
-
the chuck on my cmcd700c1 wobbles slightly when i run the drill, is the chuck broken or can i tighten it?
The wobble you are experiencing in your Craftsman V20 CMCD700C1 is typically caused by one of two things: a loose chuck retaining screw or a misalign…
-
why does my craftsman drill slow down and sound strained when i put any pressure on it, even with a fresh battery?
The "straining" sound and sudden drop in RPMs on the Craftsman V20 CMCD700C1 are typically caused by one of two things: an incorrect torque clutch se…
-
v20 drill battery won't click into the drill solidly, it just falls out if i tilt it, how do i fix the latch?
The failure of the battery to lock into the Craftsman V20 CMCD700C1 is typically caused by a failure in the mechanical engagement between the drill's…
-
craftsman cmcd700c1 drill gets super hot in the handle after like 5 minutes of use, is that normal?
No, it is not normal for the handle of the Craftsman V20 CMCD700C1 to become "super hot" within five minutes of use. While a slight warmth in the mot…
-
my craftsman v20 drill just clicks but the chuck doesn't spin at all, battery is charged, what's wrong?
The "clicking" sound you hear when pulling the trigger on your Craftsman V20 CMCD700C1 is the sound of the electronic variable speed switch engaging …
-
the led work light on the front of my saw won't turn on anymore
The Ryobi ONE+ 18V Reciprocating Saw P519 is designed for high-vibration demolition work, which is the primary enemy of the LED work light circuitry.…
-
there's a bad burning smell coming from my saw near the motor, and sometimes a little smoke
The burning smell and smoke emanating from the motor housing of your Ryobi ONE+ 18V Reciprocating Saw (P519) indicate that the armature windings or t…
-
i can't get the variable speed to work on my p519, it's only full blast or nothing
The Ryobi P519 uses a variable-speed trigger assembly that relies on a potentiometric contact system to modulate the voltage sent to the motor. When …
-
the saw vibrates way more than it used to, it's shaking my arm numb on long cuts
Excessive vibration in the Ryobi ONE+ 18V Reciprocating Saw P519 typically stems from a loss of mechanical synchronicity between the motor's eccentri…
-
the shoe on my reciprocating saw is super wobbly and slides around when i'm trying to cut
The "shoe" (or base plate) on the Ryobi ONE+ 18V Reciprocating Saw P519 is designed to pivot to allow for angled cuts. However, when it becomes "wobb…
-
my ryobi saw just stopped running mid-cut, now it doesn't do anything when i pull the trigger
The Ryobi ONE+ 18V Reciprocating Saw (P519) is prone to sudden shutdowns during heavy-duty cutting, most commonly caused by the internal thermal over…
-
the blade clamp on my p519 is stuck, i can't get the old blade out no matter how hard i pull
The Ryobi ONE+ P519 utilizes a tool-less, spring-loaded locking collar system. When a blade becomes "stuck," it is almost always due to one of two th…
-
my ryobi reciprocating saw is making a really loud grinding noise when i pull the trigger, sounds awful
The loud, metallic grinding noise occurring immediately upon trigger pull on the Ryobi P519 is typically caused by the failure of the pinion gear or …
-
weird high pitched whining noise from my bosch drill when i pull the trigger, even without load.
The high-pitched whining noise in the Bosch PS31-2A is typically caused by a misalignment or failure in the motor's rotational stability, specificall…
-
battery doesn't seem to charge all the way, fuel gauge shows one bar then charger light goes green fast.
The Bosch 12V Max PS31-2A uses a lithium-ion battery pack consisting of three cells in series. The issue you are experiencing—where the fuel gauge sh…
-
my drill driver works but the led worklight doesn't come on anymore.
The failure of the LED worklight on the Bosch PS31-2A is typically caused by a break in the electrical continuity between the trigger switch and the …
-
the forward/reverse slider switch is stuck and won't move on my ps31.
The forward/reverse slider switch on the Bosch PS31-2A typically jams due to the accumulation of fine particulate matter—specifically gypsum dust fro…
-
how do i clean out the vent slots on my bosch drill, it's full of sawdust after a drywall job.
Drywall dust, specifically the gypsum and calcium sulfate found in sheetrock, is an insidious contaminant for the Bosch 12V Max PS31-2A. Unlike wood …
-
drill seems weak, bogs down instantly driving a 2 inch screw into pine, feels like no torque.
The loss of torque in the Bosch PS31-2A is typically caused by a failure in the power delivery circuit, specifically the electronic variable speed tr…
-
the chuck on my ps31-2a wobbles a bit when a bit is in it, makes holes not perfectly round.
The wobbling you are experiencing is known as "runout." In the Bosch PS31-2A, this occurs when the concentricity of the chuck's internal jaws is comp…
-
my bosch ps31 drill driver just blinks a red light when i pull the trigger, no power at all.
The flashing red LED on your Bosch PS31-2A indicates a critical communication failure between the battery's Battery Management System (BMS) and the t…
-
dust and chips keep getting blown back right into my face from the front of the tool, didn't used to do this
The Milwaukee M18 Fuel Reciprocating Saw (2821-20) utilizes a specific airflow design where the motor's cooling fan creates a pressure differential. …
-
the variable speed trigger doesn't work right, it's either full power or nothing, no in-between control
The loss of variable speed control on the Milwaukee M18 Fuel Reciprocating Saw (2821-20) is almost always caused by a failure of the internal potenti…
-
my saw just suddenly stopped in the middle of a cut, now it smells like burnt electronics
The sudden cessation of operation accompanied by a distinct "burnt electronics" smell indicates a catastrophic failure of the MOSFETs (Metal-Oxide-Se…
-
the tool vibrates way more than it used to, feels really harsh in my hands even with a new blade
The excessive vibration in the Milwaukee M18 Fuel Reciprocating Saw (2821-20) is typically caused by a failure in the internal kinetic balancing syst…
-
the shoe on my reciprocating saw wobbles side to side a lot, makes cutting straight impossible
The lateral wobble in the shoe of the Milwaukee M18 Fuel Reciprocating Saw (Model 2821-20) is typically caused by excessive play in the pivot assembl…