Pressure Washers (Page 2)
-
the unloader valve on my ms3125 is leaking water really bad from the sides when i'm using it.
The unloader valve assembly has internal seals that direct high-pressure water. A leak from the body means those seals are worn or damaged, or the va…
-
my megashot won't start at all, not even a sputter. i checked for spark and it's good, gas is fresh.
With good spark and gas, the engine should at least cough. The fact it doesn't points to a lack of fuel actually making it into the cylinder. On thes…
-
oil is leaking from the bottom of the pump on my simpson, looks like it's coming from a little plug. is that bad?
That's the pump oil drain plug. If it's leaking, the seal (usually an O-ring or crush washer) has failed. The pump uses a special non-detergent SAE 3…
-
pressure washer surges and pulses really bad, can't hold a steady stream. it's a megashot 3125.
That pulsing is almost always caused by air getting into the water supply side of the pump. The pump is trying to pressurize a mix of air and water. …
-
just got my ms3125 and it runs for a minute then dies like it's out of gas, but the tank is full.
Yeah, this one's common on new units. The fuel tank cap isn't venting properly, creating a vacuum that starves the engine of fuel after it burns thro…
-
my simpson megashot starts fine but the pump just hums and won't build any pressure, what gives?
That's the pump motor humming but the piston assembly inside isn't moving. On these, the most common culprit is that the pump was stored with water i…
-
i can't get the high pressure hose to click and lock onto the spray wand, it just pulls right off
The quick-connect system on the wand isn't engaging. This is usually because the locking collar isn't retracting properly or the little metal balls i…
-
the motor on my ryobi sounds really loud and grinding, not the normal pump sound
A grinding noise from the motor area, distinct from the pump's normal clicking, suggests a mechanical failure. This is often a bearing in the motor o…
-
my pressure washer runs fine but then just loses all pressure and only sprays a trickle
A sudden, complete loss of pressure almost always points to a failure in the high-pressure hose or a connection, not the pump itself. You've likely d…
-
the chemical injector on my ryobi 2300 isn't pulling soap, it just sprays plain water
The chemical injector works on a suction principle. If it's not pulling, either the suction tube is blocked/not submerged, the inlet filter is clogge…
-
water is leaking from the bottom of the pump on my ryobi, right where the housing connects
A leak from the pump body usually means one of the O-rings or seals on the pump head has failed. It's a common wear item, especially if the unit was …
-
ryobi pressure washer turns on for a second then shuts off by itself, the green light goes out
The thermal overload protector is kicking in and shutting the motor down because it's overheating, usually because it's trying to start under load. T…
-
the pressure is really weak or pulsing on my ryobi electric washer, like it's surging
Surging or weak pressure is a classic sign that the machine isn't getting enough water supply. It's trying to pump faster than the water is coming in…
-
my ryobi pressure washer just hums loudly but the pump won't actually start when i pull the trigger
This is almost always the pump being air-locked. The pump can't build pressure if there's air trapped inside instead of water, so the motor just stra…
-
is it normal for this pressure washer to get really hot and smell kinda like hot plastic after 15 minutes of use?
Some warmth is normal, but a strong hot plastic smell and excessive heat usually mean the pump is running dry or with insufficient water flow, causin…
-
the wand extension on my gpw1501 is stuck and i can't get it off to change the spray tip, it's really jammed on there.
This is a classic issue. Minerals in hard water or dirt can act like cement in the threads between the wand and the spray tip quick-connect. It's not…
-
the soap injector isn't sucking any detergent out of the bottle on my 1500 psi greenworks.
The suction tube inside the detergent bottle is either clogged, disconnected, or the black low-pressure soap tip is blocked or missing. First, check …
-
why does my pressure washer leak a steady drip of water from the bottom of the pump when it's just sitting turned off?
That's a leaking pump seal. All pressure washer pumps have internal seals that keep the water in the high-pressure chamber separate from the oil bath…
-
my greenworks pressure washer turns on for a second then immediately shuts off, the light goes out.
The thermal overload protector in the motor is tripping instantly. This is usually because the pump is seized or locked up, putting too much load on …
-
how do you get the pump to prime on this thing? i followed the instructions but it just pulses and sputters.
The pulsing means the pump is trying to prime but can't get a consistent water supply. This model's axial cam pump is self-priming, but it needs a so…
-
the pressure on my gpw1501 is super weak, like it's barely spraying out, even on the 0 degree tip.
This is almost always caused by a worn or damaged O-ring on the quick-connect fitting where your high-pressure hose attaches to the spray gun. A bad …
-
my greenworks 1500 psi pressure washer just hums when i pull the trigger and the pump won't engage, what gives?
You're likely dealing with a pressure washer that's air-locked or has a clogged inlet filter. The hum means the motor's getting power, but water isn'…
-
the trigger on my spray gun is stuck or really hard to squeeze, is there a way to fix it without buying a new one
Grit, scale, or corrosion has gotten into the trigger valve mechanism inside the gun. It's a simple spring-and-plunger design that gets gummed up. 1)…
-
how do i get my pressure washer to start after winter storage, it was working when i put it away
Residual water has likely frozen and damaged the pump, or it's gummed up with deposits. The pump seals and valves are the most vulnerable parts. 1) D…
-
my sun joe makes a horrible knocking or rattling sound when it's running, sounds like it's coming from the pump
That's the sound of cavitation—the pump is trying to run without enough water, or there's a severe restriction on the inlet side. It can also be a si…
-
the soap dispenser on my spx3000 isn't pulling any detergent, it just sprays plain water
The suction tube is either clogged, disconnected, or the venturi valve isn't creating suction because you're using too high a pressure tip. 1) Make s…
-
my pressure washer runs fine but has barely any pressure coming out of the wand, it's just a trickle
This is almost always an issue with the inlet water supply or a clog in the system, not the pump failing. The SPX3000 needs a good flow of water to b…
-
the spray wand on my sun joe pressure washer leaks badly right where it connects to the hose, even with a new o-ring
You're dealing with a worn or damaged quick-connect fitting, not just the O-ring. The brass collet inside the female connector gets worn or the retai…
-
why does my spx3000 keep tripping the gfci outlet every time i try to use it
Water has gotten somewhere it shouldn't, creating a ground fault. The most common culprit is moisture in the on/off switch housing or a damaged power…
-
my sun joe spx3000 pressure washer turns on but the motor just hums and won't pump any water
This is classic airlock, especially if it's the first start-up or after storage. The pump can't prime because air is trapped inside. 1) Make sure you…
-
my greenworks electric pressure washer keeps shutting off by itself after a few minutes of use
This is typically an overheating or electrical supply issue. Tripped circuit breaker: The unit draws 13 Amps. Allow it to cool, then restart. Do not …
-
what's the black turbo nozzle for on my greenworks gpw1804? can i use it on my wood deck?
The Turbo nozzle is for intense, concentrated cleaning on tough stains. Do not use it on your wood deck. It produces a 0° stream, the most powerful s…
-
greenworks pressure washer leaking water from the pump area when i turn it off, is that normal?
The Greenworks GPW1804 utilizes an axial cam pump design. When you switch the unit off, the water remaining in the pump head and the high-pressure ho…
-
how do you change the spray tip on the greenworks 1800 psi pressure washer wand? it feels stuck
First, you need to relieve the water pressure and engage the safety lock. Here's how to do it safely. Turn off the pressure washer and shut off the w…
-
can i use bleach or vinegar in my greenworks gpw1804 pressure washer to clean my patio?
You cannot use bleach or vinegar for cleaning your patio with this pressure washer. The Greenworks GPW1804 is a consumer-grade electric pressure wash…
-
my greenworks electric pressure washer is making a loud buzzing sound but the pump won't run
Yeah, this one's common. The motor is getting power but can't start, usually due to voltage or internal friction. First, unplug any extension cord yo…
-
my greenworks gpw1804 pressure washer won't start at all, no noise or anything, what's wrong?
A complete lack of response—no motor hum or pump noise—points to an interruption in the electrical circuit powering the unit. For the Greenworks GPW1…
-
the trigger on my sun joe pressure washer is stuck or locked, i can't pull it to spray, how do i unlock it?
You've likely accidentally engaged the safety lock on the trigger gun. It's a feature to prevent accidental spraying, especially during pauses. Here'…
-
can i use an extension cord with my sun joe 2030 psi pressure washer? the one i have keeps tripping it.
You can, but with strict requirements. Most problems stem from using the wrong cord. Requirements: The plug and socket of the extension cord must be …
-
sun joe spx3000 turns on but no water is coming out of the spray gun, just air, what do i check?
The "air-only" symptom on the Sun Joe SPX3000 is almost always caused by an air lock within the pump head or a failure in the intake sequence. Becaus…
-
my sun joe pressure washer is making a weird clicking noise and then stops, is this broken?
The clicking noise is likely the thermal sensor shutting the motor off to protect it from overheating, which is a safety feature, not a sign it's bro…
-
i keep blowing fuses every time i try to use my sun joe electric pressure washer, what am i doing wrong?
Yeah, this one's common. You're overloading the circuit or using the wrong setup. First, check the fuse or circuit breaker you're blowing. It needs a…
-
why is my sun joe spx3000 pulsating and surging instead of having steady pressure?
Pulsating pressure indicates the pump is sucking air or has an inadequate water supply. and checklist: Air in the inlet hose: Hold the trigger until …
-
sun joe pressure washer starts but then shuts off after a few seconds, keeps doing this, help?
This is almost certainly the thermal sensor activating due to overheating or the Total Stop System (TSS) functioning normally. If it shuts off and wo…
-
my sun joe spx3000 pressure washer won't turn on at all, no lights or anything, what's going on?
When a Sun Joe SPX3000 exhibits a complete lack of power—meaning no LED indicator lights, no motor hum, and no response from the power switch—the iss…
-
how do i switch from soap back to just water on the sun joe spx3000?
You need to bypass the detergent suction system. Here's the step-by-step. Turn off the pressure washer using the power switch. Pull the trigger on th…
-
my sun joe pressure washer keeps blowing the fuse in my garage, what gives?
The Sun Joe SPX3000 is a high-draw appliance that pulls approximately 13 to 15 amps under full load. Most standard residential garage circuits are ra…
-
i'm getting no water out of my sun joe pressure washer, motor runs fine.
Check the water supply path. The pump is likely not getting water. Connect the water. Sounds obvious, but verify the inlet hose is connected and the …
-
why is my spx3000 pulsating and the pressure is all jumpy?
Pulsating pressure indicates air in the system or a water supply issue. Primary Fix: Hold the trigger down and let the machine run until a steady str…
-
sun joe pressure washer turns on but then shuts off by itself after a minute, is it broken?
Yeah, this one's common and usually not a big deal. It's probably the thermal sensor or the Total Stop System. First, check for the Total Stop System…