All questions — page 15
Browse by Problem
-
how do i clean the heating element part inside my dash air fryer? it has grease and stuff stuck up there that won't come off.
Grease and food particles get splattered up onto the heating coil and the metal shield around it during cooking. If you don't clean it, it can smoke or burn th…
-
food keeps coming out soggy on the bottom in my dash tasti-crisp, not crispy at all, am i doing something wrong?
Soggy bottoms are almost always an overcrowding issue. You're putting in too much food at once, which blocks the hot air from circulating underneath the basket…
-
the non-stick coating on my dash fryer basket is starting to peel and flake off, is it safe to use and can i fix it?
That's the PTFE (non-stick) coating breaking down. It's caused by using metal utensils, abrasive scrubbers, or high-heat cooking sprays, which damage the surfa…
-
my air fryer makes a loud rattling noise when it's running, sounds like something is loose inside, is it broken?
That rattling is almost always the basket handle. On these models, the black plastic handle can work itself loose from its mounting points on the wire basket f…
-
my dash tasti-crisp air fryer just won't turn on when i plug it in, no lights or anything, what do i do?
This is usually a power supply issue, not a machine failure. The most common culprit is the basket not being seated all the way in, which activates a safety sw…
-
the washer just beeps three times and won't do anything when i press start.
When the Samsung WA55CG7100AW emits three rapid beeps and refuses to engage the motor upon pressing the Start/Pause button, it is triggering a safety lockout s…
-
water is leaking from the bottom front of my washer onto the floor.
Most likely source is a loose or split drain hose connection at the back of the washer or a clogged/overflowing drain standpipe. Pull the washer out. Check whe…
-
it says it's connected to wifi on the app but i can't start a cycle remotely.
The washer is in a state that blocks remote start. Common reasons: Child Lock is on, the door is physically open, or the cycle was started manually at the unit…
-
the washer lid won't unlock after a cycle ends, i can't open it to get my clothes out.
The Samsung WA55CG7100AW utilizes a solenoid-driven electronic lid lock assembly designed to prevent access during high-speed spins or when the tub is filled. …
-
my washer smells musty, especially right after a cycle finishes. how do i clean it?
This musty odor is caused by the accumulation of "scrud"—a waxy buildup of undissolved detergent, fabric softener, and organic skin cells—which traps moisture …
-
suddenly getting an ub error code on the display, washer won't drain.
The UB (Unbalanced) error on the Samsung WA55CG7100AW occurs when the machine's internal sensors detect that the laundry load is not evenly distributed around …
-
why does my top load samsung make a loud grinding noise during the spin cycle?
This is usually a foreign object caught between the washplate at the bottom of the tub and the inner tub. Coins, bra wires, and screws are common culprits. Unp…
-
my samsung wa55cg7100aw washer just shows nd and a lock symbol and won't start, what's going on?
The "nd" error code combined with the lock symbol on your Samsung WA55CG7100AW indicates that the Child Lock feature has been accidentally activated. When this…
-
it takes forever to make the first batch of ice, like over 30 minutes, is that normal?
The extended duration for the first batch of ice in a Della Portable Ice Maker is typically caused by "thermal inertia." When you first plug in the machine, th…
-
the ice tastes weird, kinda plastic-y or like vinegar even after cleaning
The "plastic" or "vinegar" taste in Della Portable Ice Makers is typically caused by one of three factors: off-gassing from the food-grade plastics during the …
-
it's leaking water from the bottom onto my counter, not from the drain plug
The leakage occurring from the bottom of the Della Portable Ice Maker, specifically when not originating from the drain plug, typically indicates a failure in …
-
my ice maker keeps flashing the 'add water' light but the tank is definitely full
The "Add Water" indicator on a Della Portable Ice Maker is triggered by a magnetic float switch located within the water reservoir. This system relies on a sma…
-
i just got this della and it won't turn on at all, no lights, nothing
A complete lack of power (no LED indicators, no fan noise, no display) on a brand new Della Portable Ice Maker typically points to a break in the electrical ci…
-
the ice cubes from my della are really thin and hollow, like shells, they melt instantly
Thin, hollow, or "shell-like" ice cubes in a Della Portable Ice Maker are almost always the result of an insufficient water volume being pumped into the freezi…
-
della portable ice maker makes a loud grinding noise when it's trying to harvest ice
The loud grinding noise occurring specifically during the "harvest" phase—the moment the machine attempts to push the frozen ice cubes off the evaporator pins—…
-
my della ice maker just beeps three times and won't make ice, what's that code mean?
The triple-beep alarm on a Della Portable Ice Maker is a specific alert triggered by the infrared (IR) sensor system. This system consists of an emitter and a …
-
smart hub keeps crashing or apps won't load on my samsung tv, just a spinning circle.
DIAGNOSIS: The TV's internal storage is likely full from cached app data, or a specific app has corrupted. The Q60D doesn't have a ton of storage for the OS an…
-
the tv speakers on my qn32q60d make a faint buzzing sound when the volume is low or off.
DIAGNOSIS: That's an electrical ground loop or interference from a nearby component, often coming through the internal amplifier. It's especially noticeable be…
-
can i clean the screen on my qled tv with water? the manual is super vague and i'm scared to ruin it.
DIAGNOSIS: You're right to be cautious. The screen has a special anti-glare and anti-reflection coating that can be damaged by chemicals or pressure. FIX: Use …
-
my q60d screen looks weirdly dim or washed out in hdr mode when i play games.
DIAGNOSIS: The TV isn't switching properly into its proper HDR picture mode, or the console/PC is sending a mismatched signal. This model has specific HDR sett…
-
how do i get rid of the annoying 'no signal' box that pops up every few minutes on my samsung tv?
DIAGNOSIS: The TV's 'Auto Source Change' or 'Input Signal Plus' feature is being triggered by a flicker or standby signal from a connected device, like a cable…
-
the remote for my samsung qled is super laggy or doesn't work unless i'm pointing right at it.
DIAGNOSIS: Yeah, this one's common. It's usually not the remote itself, but interference. The Q60D uses Bluetooth for the remote, and something nearby is drown…
-
why does my qn32q60d keep disconnecting from wifi every day? i have to reboot it to reconnect.
DIAGNOSIS: The TV's network adapter is likely getting stuck in a low-power or sleep state and failing to re-establish the connection. It's a known power manage…
-
my new samsung q60d tv just shows a black screen but the power light is on, sound works, what gives?
DIAGNOSIS: The TV is on and running, but the backlight or the local dimming system isn't kicking in. This is a very common hiccup with this model, often relate…
-
the blades seem dull, takes forever to crush ice even on the ice crush setting
DIAGNOSIS: Blender blades don't get "dull" like knives; they bend or chip. More likely, you're overloading the jar or not using the proper technique for the K1…
-
kitchenaid 3 speed only works on the highest speed now, low and medium buttons do nothing
DIAGNOSIS: The speed selector switch contacts are dirty or the switch itself has failed internally. High speed often works because it's a direct circuit. FIX: …
-
my blender jar is stuck on the base and i can't get it off no matter how hard i twist
DIAGNOSIS: The plastic drive coupler on the jar has partially melted or deformed, mechanically locking it onto the motor shaft. FIX: Do not use excessive force…
-
how do you clean the black residue off the blender's rubber drive socket? it stains my hands
DIAGNOSIS: That's wear material from the jar's plastic drive coupling rubbing against the metal motor shaft socket. It's a mix of rubber and ground-down plasti…
-
making a horrible grinding noise only on the 'ice crush' setting, other speeds are fine
DIAGNOSIS: The plastic drive coupler that engages the ice-crush mechanism is worn down or cracked. The K150 uses a specific internal gear train for the pulse/i…
-
kitchenaid k150 leaking from the bottom of the glass jar where the blades are
DIAGNOSIS: The silicone seal (gasket) under the blade assembly has hardened, cracked, or was improperly installed after cleaning. FIX: You need to replace the …
-
blender just stopped working mid-use, now it won't turn on at all, no lights or noise
DIAGNOSIS: The unit's internal thermal fuse or breaker has blown, cutting all power. This usually happens from overloading or a voltage spike. FIX: Check your …
-
my kitchenaid blender motor just hums loudly and the blades won't spin at all
DIAGNOSIS: You have a severe jar-to-base misalignment or jam. The motor's thermal overload protector has likely tripped to prevent burnout because the blade as…
-
i got a new phone and now the glas app won't find or connect to my thermostat. it still works on the wall.
The issue is not a failure of the thermostat hardware or the local Wi-Fi connection, but rather a failure of the cloud-based authentication handshake between y…
-
the temperature reading on my glas seems way off compared to other thermometers in the house.
The Johnson Controls GLAS Smart Thermostat utilizes a high-precision thermistor located internally. When the displayed temperature deviates significantly from …
-
how do i clean the white plastic outer case? it's getting yellow and dirty but i'm scared to damage it.
The discoloration on the Johnson Controls GLAS Smart Thermostat is typically caused by a process called photo-oxidation. The outer bezel is constructed from a …