Dishwashers (Page 2)
-
the touch controls on the front of my dishwasher don't respond or beep when i press them
The unresponsive touch panel on the Samsung DW80CG4021SR is typically caused by a failure in the capacitive sensing layer or a communication breakdow…
-
getting an 'OE' error code at the end of every cycle, what causes that?
The 'OE' error code on your Samsung DW80CG4021SR indicates a "Drain Error," meaning the control board has detected that water is still present in the…
-
samsung dishwasher won't turn on at all, no lights, no display, nothing
Complete loss of power. This is usually a supply issue, not the appliance itself. Check the power source and the door latch first. Verify the circuit…
-
dishwasher runs but leaves a white chalky film on everything, especially glasses
This is hard water scale buildup. The internal water softener system may be depleted or not functioning. This model has a built-in water softening sy…
-
dw80cg4021sr dishwasher is making a loud grinding or buzzing noise during the wash cycle only
This is almost always a foreign object caught in the wash arm assembly or the wash pump impeller. A utensil or piece of glass is the usual suspect. R…
-
my samsung dishwasher just shows a flashing 'cE' on the display and won't run, what does that mean?
The cE error is a communication failure between the main control board and the user interface board. It's a common failure point on this model. Unplu…
-
the normal cycle seems to run forever, like over 3 hours, is that right?
Cycle times are excessively long. This is normal operation for sensor cycles. The LDTS5552S uses a soil sensor to adjust time, temperature, and water…
-
water is not draining at the end of the cycle, there's standing water in the bottom.
Standing water in the tub after a cycle. This is a drain system obstruction or pump failure. First, check for a clog in the drain hose. Disconnect po…
-
the control panel buttons don't respond or light up, the whole thing is dead. checked the outlet and breaker.
The unit has no power. The outlet and breaker are confirmed good. The issue is internal: a blown thermal fuse or a failed main control board. Check t…
-
getting an le error code on my lg ldts5552s, what does that mean and how do i fix it?
The display shows LE (Leak Error). The leak sensor in the base pan has detected water. This triggers an immediate stop to the cycle. First, check for…
-
it won't start when i press the start button, just beeps once. all the lights are on.
The control panel is responsive but the unit beeps and will not start. This is a door latch or child lock issue. Ensure the door is fully latched. Op…
-
dishes are still wet and spotted after a normal cycle, nothing seems to be drying.
Dishes are wet and spotted at cycle end. The most likely cause is a disabled heating element or incorrect rinse aid setting. First, ensure the heatin…
-
my lg dishwasher is making a loud grinding noise during the wash cycle, sounds like it's coming from the bottom.
A loud grinding noise from the wash tub. The most common cause is a foreign object caught in the wash arm or pump assembly. Inspect the lower spray a…
-
lg dishwasher ldts5552s just shows pf on the display, what is that? it won't run any cycle.
The display shows PF (Power Failure). The control board detected a power interruption during a cycle. Clear the PF code. Press and hold the Cycle Sel…
-
my dishwasher is leaking from the bottom left corner, right onto the floor.
A leak from the front corner typically points to the door gasket or the water inlet valve, not the tub itself. Inspect and clean the door gasket (sea…
-
the sanitize light never comes on, even after a full cycle. how do i know it's working?
The sanitize indicator only illuminates if the final rinse water reached 155°F. The water heater may be set too low, the cycle was interrupted, or th…
-
the dishwasher leaves standing water in the bottom after a cycle, not draining completely.
The drain path is obstructed. This is a clog in the filter, drain hose, or air gap/disposal connection. Clear the drain path from internal to externa…
-
the control panel buttons are beeping but not responding when i press them, or they act like i'm pressing different buttons.
Moisture or condensation has gotten behind the touch-sensitive control panel, causing a short or 'phantom' presses. Dry out the control area with a f…
-
dishes are coming out with white chalky film or powder all over them, especially on glasses.
This is hard water detergent residue. You're either using too much detergent, the wrong type, or your rinse aid dispenser is empty/off. Adjust your d…
-
it's making a loud grinding or humming noise only during the drain cycle, sounds awful.
A foreign object—like a broken piece of glass, bone, or utensil—is caught in the drain pump impeller. You need to access and clear the drain pump. Di…
-
just installed this ge dishwasher and it won't start at all, no lights, nothing. checked the breaker and it's on.
This is almost always an installation/power supply issue, not a machine failure. The door latch or power connection isn't complete. Check the door la…
-
my ge dishwasher gdp665synfs says 3 hours left at the start and then never counts down, just stays there forever. is it even running?
You're likely seeing the 'Time Remaining' display glitch, a common software hiccup. The cycle is probably running, but the timer display is frozen. P…
-
the third rack on top is sagging in the middle and my tall cups don't fit anymore, can i tighten it?
The Top Track silverware rack's support rails are made of a relatively flexible plastic. Over time, especially with heavy items placed in the center,…
-
my dishwasher is flashing "F7E1" and beeping. what does that mean and how do i make it stop?
F7E1 is a communication error between the main control board and the user interface (UI) board. The two boards aren't talking, so the machine faults.…
-
the door latch on my dishwasher won't catch, so i can't start it. i have to hold the door shut with a chair. is this a quick fix?
The door latch mechanism (the part on the door frame, not the tub) has likely failed. On this model, it's a known issue where the plastic housing of …
-
why does my whirlpool dishwasher keep stopping mid-cycle and just sit there with the time remaining displayed? it's not flashing any errors.
This model has a 'sensing' phase at the start of most cycles. If the water isn't getting hot enough, it will pause indefinitely, waiting. The most co…
-
my dishwasher is leaving a gritty white film on all my glasses and plates after a cycle, even with rinse aid full.
That's hard water scale. This model has a built-in water softener that uses a special salt (not the same as rinse aid), but it needs to be refilled a…
-
the control panel on my whirlpool dishwasher is completely dead, no lights, no response, but i can hear a faint hum from inside. help?
This is almost always a failed user interface (UI) board. The faint hum means main power is reaching the machine, but the touchpad and display aren't…
-
my whirlpool dishwasher just says "clean filter" and won't start any cycle, i already rinsed the filter what gives?
The 'Clean Filter' indicator is a maintenance reminder, not a blockage alert. It triggers automatically after a set number of cycles, regardless of t…
-
it just stopped mid-cycle and now the drain pump seems to be running continuously, a humming sound from the bottom.
A drain pump that won't stop humming means it's trying to pump but can't move water. This is almost always a blockage in the drain hose or a stuck ch…
-
the touch buttons on the front panel are really unresponsive, i have to press them super hard or multiple times.
Yeah, this one's common. Over time, moisture and steam can seep behind the membrane of the touch control panel, causing the contacts to degrade or ge…
-
dishes are still wet and streaky at the end of the cycle, even on the extra dry setting.
Poor drying, especially on a model with a condensation drying system like this one, usually comes down to three things: rinse aid, loading, or a faul…
-
the display just flashes and it beeps three times when i try to start it, then nothing happens.
The triple beep with flashing lights is this model's standard error indication for a water supply issue. The machine isn't getting enough water, or i…
-
it's making a really loud grinding or rattling noise during the wash cycle, sounds like it's coming from the bottom.
A loud grinding noise from the pump area is classic for a foreign object—like a piece of broken glass, a bone, or a cherry pit—getting stuck in the i…
-
my beko dishwasher leaves a white, chalky powder all over everything, especially glasses. what is that?
That's dried detergent residue, usually from using the wrong type of tablet or powder in combination with hard water. The DUT25401X has a built-in wa…
-
the door on my beko dishwasher won't stay closed, it just pops open during a cycle and everything stops.
This is almost always a problem with the door latch mechanism. The little plastic hook on the door or the catch assembly in the frame wears out or br…
-
my beko dishwasher just shows three dashes '---' on the display and won't start, what's that about?
The display showing "---" usually means the control board is in a factory default state or has lost its configuration. This can happen after a power …
-
dishes are coming out with white, chalky residue all over them, especially glasses.
That's hard water scale or detergent that hasn't rinsed off properly. The most common cause on this model is a clogged or malfunctioning rinse aid di…
-
the screen on the front just says 'remote' and i can't make it do anything with the buttons.
The dishwasher is stuck in "Remote Enable" mode, which locks out the local controls for use with a home automation system or remote start. To cancel …
-
the door won't latch shut unless i really slam it hard, and sometimes it pops open mid-cycle.
The door latch mechanism is out of alignment or the strike plate is worn. This model has a motorized latch, and if it's not engaging smoothly, it'll …
-
the 'sanitized' light never comes on even after running a sani-rinse cycle. is it broken?
The sanitize indicator requires the final rinse water to hit 150°F. If the light doesn't come on, the water isn't getting hot enough, or the high-lim…
-
it's making a loud grinding noise during the wash cycle, sounds like it's coming from the bottom.
That's the sound of the wash pump impeller chewing on something it shouldn't. A piece of glass, a bone, or a utensil has likely gotten past the filte…
-
the third rack on top barely gets anything wet, everything comes out bone dry and still dirty.
The top spray arm isn't getting enough water pressure. This is usually because the upper arm is clogged with hard water scale or debris, or the suppl…
-
dishwasher is flashing 'E24' on the display and won't start a cycle. what does that mean?
Yeah, this one's common. E24 is a drain error. The dishwasher thinks there's water left in the sump after it tried to drain, or it can't activate the…
-
my thermador star sapphire dishwasher won't turn on at all, no lights, nothing. it's plugged in and the breaker is fine.
You've got a dead control panel. This is almost always a failed electronic control board, which is the brain of this dishwasher. Power's getting to t…
-
after a cycle, the inside of my miele still smells musty, like wet towels. i run the cleaning tablet monthly. what else can i do?
That musty smell is mildew growing in hidden, damp areas the main wash doesn't hit. The usual culprits are the rubber door gasket, the float chamber …
-
the autodos status light is flashing yellow, not green or red. the app just says 'check autodos'. what does yellow mean?
A flashing yellow light is a warning state. It means the AutoDos system has detected an irregularity—usually that the PowerDisk cartridge is very low…
-
there's a loud grinding noise coming from the bottom during the wash cycle, sounds like metal on metal. is the pump going out?
That's almost certainly something hard—a piece of broken glass, a bone, a utensil—that's gotten past the filters and is now in the circulation pump i…
-
i keep getting an f16 error code on the display and the cycle stops. what does that mean and how do i clear it?
F16 is a water intake error. The dishwasher didn't get enough water within the expected time at the start of a cycle. The usual suspects are a kinked…
-
the display on my g7566scvi is completely dark, no lights, no response to buttons, but i can hear a faint hum from inside. is it dead?
The control panel/display unit has lost power, but the main board or motor might still be getting juice, hence the hum. This often points to a blown …