All questions — page 38
Browse by Problem
-
the fan in my leisure 3w is ridiculously loud, sounds like a jet engine, is this normal?
It's definitely not supposed to be a jet engine. The most likely cause is the projector's air vents are blocked or it's sitting on a surface that's trapping he…
-
just got my vankyo leisure 3 and the picture is super blurry no matter how i focus the lens, what gives?
This isn't just a focus issue. The most common cause is that you're using keystone correction (digital picture adjustment) to try and square up the image inste…
-
i’m getting no sound from my built-in tv speakers when i switch to an hdmi input like my playstation
The TV is likely receiving an audio format from your external device that its internal speakers can’t decode, like Dolby Digital or DTS. It’s an HDMI handshake…
-
the motion on my qled looks weird and jittery during sports or fast scenes, even with motion smoothing off
This is often the ‘Judder Effect’ from the TV’s native 60Hz panel struggling with 24 or 30 frames-per-second content. The default Auto Motion Plus settings can…
-
my tv remote (tm2340a) is super laggy or doesn’t respond unless i point it right at the tv
The SolarCell remote uses both RF (radio frequency) and IR (infrared). The lag or need to point means it’s falling back to the slower IR mode because the RF co…
-
how do i properly clean the screen on my qn43q60d without messing up the coating?
You’re right to be cautious. Using the wrong cleaner or cloth can damage the anti-glare and anti-smudge coatings on QLED screens. Use only a dry, soft, lint-fr…
-
there's a faint but annoying high pitched buzz coming from the back of my samsung qled, is this normal?
That’s coil whine, a high-frequency noise from the power supply components. It’s not dangerous, but it can be irritating, especially in a quiet room. First, ch…
-
my qn43q60d keeps saying network disconnected even though my wifi is fine, streaming apps won’t open
The TV’s wireless connection is dropping or failing to authenticate. It’s a common handshake problem between the TV’s network hardware and some routers. 1) Go …
-
my new samsung 60d tv won't power on, no lights, nothing at all, it's like it's dead
This is almost always a power supply issue, either at the wall or the connection to the TV itself. The internal power board is rarely the first culprit. Start …
-
the up button on my handset works but the down button is unresponsive.
The membrane switch for the down button inside the handset is faulty or the wire connecting it is damaged. Moisture or physical damage is the usual cause. You …
-
my desk wobbles side to side a lot when it's at standing height, is this normal?
No, excessive wobble is not normal. The crossbar may not be tightened properly, or the floor is uneven causing the feet to not sit flat. Lower the desk. Check …
-
desk just stopped working, no lights on the control panel at all. checked the outlet and it's fine.
No power to the control box. The issue is either the power supply brick, the cable from the brick to the desk, or the internal fuse in the control box. First, …
-
how do i clean the white laminate top without damaging it? i got some stains that won't come off.
The ApexDesk Elite Series utilizes a high-pressure laminate (HPL) surface. While this material is designed for durability, the white finish is susceptible to "…
-
the memory height settings on my controller keep getting lost after a power outage.
The ApexDesk Elite Series utilizes a non-volatile memory chip that is supposed to retain height presets (1-4) even during power cycles. However, in many Elite …
-
my desk makes a loud grinding or clicking noise from one leg when it moves.
The loud grinding or clicking noise in an ApexDesk Elite Series leg is typically caused by a misalignment in the internal drive screw or the accumulation of pa…
-
set up my new apexdesk and one leg goes up but the other lags behind or doesn't move at all.
The control box is not properly synced to both motors. The legs are out of sync from the initial setup. Lower the desk to its absolute bottom position. Unplug …
-
my apexdesk elite just beeps and won't move when i press the up or down buttons, what's wrong?
The beeping sound and lack of movement on your ApexDesk Elite Series typically indicate that the control box has entered a "Protection Mode." This is most comm…
-
after folding and unfolding, my scooter sometimes won’t power on until i jiggle the stem.
An intermittent connection in the wiring harness that runs through the folding hinge. The repeated folding fatigues the wires. Unfold the scooter and ensure it…
-
i can’t get the inokim app to connect to my scooter via bluetooth, it just keeps searching.
The scooter's Bluetooth module may not be in pairing mode, or there is an app permission conflict. First, ensure the scooter is powered ON. Open the Inokim app…
-
the front fender on my light 2 super rattles nonstop over small bumps, driving me nuts.
The rattling on the Inokim Light 2 Super is caused by a combination of mechanical play in the plastic mounting brackets and a lack of vibration dampening betwe…
-
the battery indicator drops from 3 bars to 1 bar almost instantly after a full charge, is my battery dead?
The sudden drop from 3 bars to 1 bar on the INOKIM Light 2 Super is typically not a sign of a completely "dead" battery, but rather a symptom of severe cell im…
-
how do i clean the deck and underside without messing up the electronics? i rode through some mud.
The Inokim Light 2 Super features a sleek, integrated design, but the deck is not hermetically sealed. Mud is particularly dangerous because it acts as a spong…
-
my scooter turns on but the motor doesn’t engage when i press the throttle, just a clicking sound from the deck.
The clicking sound you hear coming from the deck is the audible activation of the main power relay within the controller. This indicates that the logic board i…
-
the folding mechanism on my light 2 super is super stiff and squeaks like crazy, how do i fix it?
The stiffness and audible squeaking in the INOKIM Light 2 Super folding mechanism are caused by the accumulation of road grit, micro-dust, and oxidation on the…
-
my inokim light 2 super just beeps three times when i try to turn it on and nothing happens, what’s wrong?
The triple beep is a throttle fault code. The scooter's control system detects the throttle is not in its neutral position at startup. First, ensure the scoote…
-
my arlo baby won't charge on the dock, the light just pulses white and it dies
The magnetic charging contacts on the bottom of the camera or on the dock are dirty or corroded, breaking the connection. Power everything down. Inspect the fo…
-
how do i clean the arlo baby camera cover? it's got dried milk spots and i'm scared to ruin it
The removable fabric cover is machine washable, but the plastic camera body and lens need careful handling. For the fabric cover: simply unzip it, remove it, a…
-
the audio on my arlo baby is super quiet even with volume maxed, i can barely hear my baby
The microphone on the camera might be partially blocked, or more commonly, the audio stream is being compressed too much due to a poor WiFi connection. First, …
-
the temperature reading on my arlo baby is always way off, like it says 80 degrees when it's 72
The internal temperature sensor is being heated by the camera's own electronics. It's a design flaw—if the camera is plugged in and running hot, or in a sealed…
-
i can't get the arlo baby to connect during setup, it just flashes amber and never shows up in the app
The camera is stuck in its pairing/sync mode. A flashing amber light means it's looking for a connection but can't find your network or phone. Force a fresh st…
-
why does my arlo baby make a loud clicking noise every few minutes? it's coming from the base.
That's the sound of the physical privacy shutter opening or closing. Yeah, it's jarring. It happens when you toggle the camera on or off in the app, or if the …
-
the night vision on my arlo baby is super grainy and i can barely see anything, is it broken?
The infrared LEDs for night vision are either dirty or there's an object blocking them. A layer of dust or a stray crib bumper can completely scatter the IR li…
-
my arlo baby camera keeps going offline and the app says it's disconnected even though my wifi is fine
The camera is losing its connection to your WiFi router, which is the most common gripe with this model. It's usually a signal strength or network congestion i…
-
the power light turns on but absolutely nothing happens, no heat, no spin, when i press the button.
The fact that the power light illuminates indicates that the primary AC power is reaching the device's logic board, but the failure of both the heating element…
-
it randomly stops spinning in the middle of curling a section, then starts again later. so inconsistent.
The inconsistent spinning behavior in the CHI Spin N Curl is almost always caused by an intermittent failure in the drive motor's torque delivery or a thermal …
-
the rotating part of the barrel feels wobbly and loose, is it supposed to be like that?
The rotating barrel of the CHI Spin N Curl is designed to be securely locked into the drive mechanism; any noticeable "wobble," lateral play, or feeling of loo…
-
my curls fall out immediately after using the spin n curl, it’s like it doesn’t get hot enough even on high.
The issue where curls drop immediately on the CHI Spin N Curl is rarely a failure of the heating element; rather, it is a failure of "thermal setting." For a c…
-
the clamp on my spin n curl won’t stay closed, it just pops open when i try to put hair in it.
The failure of the CHI Spin N Curl clamp to remain closed is typically caused by a buildup of "product sludge"—a mixture of heat-protectant sprays, pomades, an…
-
how do you clean the actual ceramic barrel? it feels sticky and my hair is snagging on it now.
The sticky sensation and snagging on your CHI Spin N Curl barrel are caused by "product polymerization." When you use heat-styling tools over hair treated with…
-
the curling barrel gets super hot but it won’t rotate or spin for me, just sits there heating up.
The CHI Spin N Curl is designed with a safety-interlock mechanism that prevents the motor from rotating unless the clamp is fully engaged. When the barrel heat…