All questions — page 160
Browse by Problem
-
the washer won't drain at all, just sits there with water in the tub at the end of the cycle.
A non-draining washer is typically caused by a clog in the drainage path. The usual suspect is a foreign object (sock, coin, hair tie) stuck in the drain pump …
-
a musty smell is coming from the washer even after i run cleaning cycles.
The smell is mold and mildew growing in hidden damp areas: primarily the rubber gasket/ring around the top of the drum (the "bellow") and in the dispenser draw…
-
the control panel is totally dead, no lights, no response, but it's plugged in.
A completely dead panel points to a power supply issue, not a control board failure (yet). The most common cause is a tripped thermal fuse on the main power li…
-
i get an 'ie' error every time i try to run a cycle, water just trickles in.
"IE" stands for "Inlet Error" — the washer isn't getting enough water within the expected time frame. The primary cause is restricted water flow, usually from …
-
after a wash, my clothes are sopping wet like the spin didn't work at all.
Inadequate spinning is almost always an unbalanced load. The washer's sensor detects an imbalance and drastically reduces spin speed (or skips it) to prevent d…
-
the 'turbo wash' cycle takes forever, like over an hour, i thought it was supposed to be fast.
The TurboWash cycle time is adaptive. It adds time if it senses the load is very large, heavily soiled, or out of balance. Your machine is likely adding extra …
-
washer makes a horrible grinding noise during the spin cycle, sounds like metal on metal.
A severe grinding or scraping noise during spin points to the spider arm — the central component that holds the drum — being cracked or broken. On LG top loade…
-
my lg top loader keeps saying 'le' on the display and won't start the cycle, what does that even mean?
That's "LE" for "LEak" — your washer's leak sensor in the base has detected water where it shouldn't be. It's a safety lockout to prevent a flood. The cause is…
-
after a cycle, the clothes are sopping wet like it didn't spin all the water out.
If the washer completes the cycle but leaves clothes dripping, the spin function failed. This could be due to an unbalanced load (which cancels the spin), a fa…
-
it's unbalanced on every spin and makes a loud banging, then stops.
The washer is detecting an 'out-of-balance' load. This happens when clothes are all clumped on one side of the basket. The machine will try to redistribute the…
-
the lid lock light just keeps blinking and it won't run, even though the lid is closed.
The washer thinks the lid is open or the lock mechanism is faulty. This is a safety feature. The problem is usually the lid switch assembly itself or the plast…
-
it fills up with water super slow, takes forever to start a load.
A slow fill is almost always a water supply issue, not the washer itself. The inlet valves on the machine are fine, but they aren't getting enough water pressu…
-
how do i clean the filter on my whirlpool washer? it smells musty.
The musty smell comes from mildew growing in hidden, damp places. While there's a cleaning cycle, the main culprit for odor is often the drain pump filter, whi…
-
washer won't start, just beeps once when i press power and nothing lights up.
That single beep with no display usually means the control board is getting some power, but the main user interface (the part you press) isn't communicating. I…
-
my top load whirlpool is making a loud grinding noise only on the spin cycle, sounds awful.
A grinding or scraping noise during the spin is almost always something caught between the inner wash basket and the outer tub, or a worn-out drive system comp…
-
my whirlpool washer just says F21 and won't drain at all, what does that mean?
That's a drain error. Your washer is trying to pump the water out but it's not working, usually because the drain hose or pump is clogged, or the pump itself h…
-
the smart things app won't connect to my washer, it just times out during the wifi setup.
Weak 2.4 GHz WiFi signal at the washer's location. Or a network password/encryption type mismatch. The washer's WiFi module is not powerful. Move your router c…
-
the washer is walking across the floor during spin, it's really loud and vibrating.
The shipping bolts weren't removed. Or the washer is severely unlevel. The four large bolts in the back secure the drum for transit. Unplug the washer. Tilt it…
-
there's a bad musty smell coming from inside the drum even after i run a clean cycle.
Bio-film and mildew in the hidden spaces. The rubber gasket around the top of the tub, the detergent dispenser, and the sump hose are prime spots. Run a Self C…
-
it keeps stopping mid-cycle and the display says 'nF' or 'no fill'. water trickles in super slow.
nF is a no-fill error. Low water pressure or a clogged inlet valve screen. The washer times out waiting for enough water. Turn off both hot and cold water supp…
-
clothes are sopping wet at the end of the cycle, washer didn't spin them out.
The Samsung WA50R5400AW utilizes a sensitive electronic balance sensor integrated into the tub suspension system. When the washer detects that the load is skew…
-
the lid won't lock, it just clicks and the cycle won't start. sometimes it says 'dE'.
The "dE" error code on the Samsung WA50R5400AW specifically indicates a "Door Error," meaning the control board is not receiving the required confirmation sign…
-
washer makes a loud grinding noise during the spin cycle, sounds like metal on metal.
The loud, metal-on-metal grinding noise during the high-speed spin cycle on the Samsung WA50R5400AW is typically caused by the failure of the spider arm (the f…
-
my samsung wa50r5400aw washer just shows '5E' on the display and beeps, then shuts off. what does that mean?
5E is a drain error. The washer can't pump out the water. The drain hose is kinked, clogged, or installed too high. Unplug the washer. Pull it out. Check the d…
-
my washer stopped mid cycle and now the display is blank, no lights, completely dead.
A completely blank display and no power indicates a loss of electrical supply to the control board. The primary suspects are a tripped household circuit, a fau…
-
the washer is shaking violently and moving across the floor during the spin, even with balanced loads.
Violent shaking and walking indicates the suspension rods or springs are damaged, or the shipping bolts were not removed. On this model, four suspension rods w…
-
how do i run a clean cycle on this ge washer? i don't see a specific button for it.
The GTW465ASNWW does not have a dedicated "Clean Washer" button. The cleaning cycle is initiated through a specific combination of settings. Ensure the washer …
-
it won't go into spin cycle, just keeps agitating forever and the clothes are sopping wet.
The washer is stuck in a continuous agitation phase and will not advance to spin. This is often caused by a failed lid lock switch or a faulty signal from it. …
-
the washer fills super slow, like it takes 20 minutes just to get enough water to start agitating.
Extremely slow filling points to a restricted water inlet. The most common cause is clogged inlet screens inside the water valve where the hoses connect. Turn …
-
water is leaking from the bottom front of my ge gtw465 washer, right under the door area.
A leak from the front-bottom area, near the door, typically comes from the drain pump or its connecting hoses. The pump housing or its seal can crack, or a hos…
-
washer is making a loud grinding noise only on the agitate part of the cycle, spin is fine.
A loud grinding noise during agitation, with normal spin, indicates a problem with the agitator dogs or the agitator itself. On this model, worn plastic agitat…
-
my ge top load washer gtw465asnww just keeps saying 'unb' and won't start a cycle, what does that mean?
The display is showing "unb". This is the "unbalanced load" error code for your GTW465ASNWW. The washer detected an uneven distribution of laundry during the s…
-
it won't finish a cycle, just stops partway through and sits there with the timer stuck. no error codes.
The washer is likely stuck waiting for a condition to be met, most commonly because it's not filling or draining properly, or a temperature sensor is taking to…
-
the washer shakes and walks violently across the floor during the spin, it's really loud.
The load is severely out of balance, or the suspension rods/springs that stabilize the tub have worn out or failed. An unbalanced load is the first thing to ru…
-
all the lights on the control panel are flashing and it's completely unresponsive, won't do anything.
The main control board has likely locked up or detected a fault. It's essentially having a full-system panic attack. Perform a hard reset. Unplug the washer fr…
-
my washer won't drain at all, just sits there with water in the bottom at the end of the cycle.
The drain pump is either clogged or has failed. A clog is way more likely—something like a small sock, hair, or a coin has jammed the impeller. Unplug the wash…
-
how do i clean the filter on my speed queen top loader? i can't find it anywhere.
You're looking for a pump filter, but the TR7003WN doesn't have a user-serviceable lint filter or pump clean-out like some front-loaders. The main filtration i…
-
it fills with water super slow, takes forever to start washing. water pressure everywhere else is fine.
The inlet water valves on the back of the washer are probably clogged with sediment or mineral scale. Yeah, this one's common, especially if you have hard wate…
-
the washer is making a loud grinding noise only during the spin cycle, sounds like metal on metal.
That's almost certainly the spider arm—the big three-armed bracket that holds the inner tub to the drive shaft. On some older TR7003WN units, it can corrode an…
-
my speed queen tr7003wn washer just keeps beeping non-stop and won't start a cycle, what's wrong?
The washer is stuck in a beeping alarm state, usually because the lid isn't closed and latched properly. The lid switch on these is pretty particular. First, j…