All questions — page 161
Browse by Problem
-
it's not filling with enough water, even on the deep water wash setting, clothes are dry on top.
The most likely cause is a clogged or slow-filling water inlet valve screen, restricting flow. Turn off both hot and cold water supply valves behind the washer…
-
the clean washer light is flashing and i can't get it to turn off, how do i reset it?
The washer's reminder system is alerting you that it's time to run a cleaning cycle. It's a timer-based reminder, not a sensor. Run a Clean Washer cycle. Selec…
-
it's vibrating and walking across the floor violently on high spin, really loud.
The washer is out of level, or the shipping bolts (or one of them) were not fully removed during installation. First, confirm all four shipping bolts at the ba…
-
the lid lock light just keeps blinking and it won't start or let me open it.
The washer isn't registering that the lid is fully closed and latched, so it won't engage the lock or start. Ensure nothing (like a sock or label) is obstructi…
-
it's leaving dark gray or black greasy streaks on my clothes, only on certain loads.
The appearance of dark gray or black greasy streaks on your Maytag MVW7230HW is typically caused by a failure of the tub seal or a leak in the transmission gea…
-
clothes are still soaking wet at the end of the cycle on my lg front loader, not spun dry.
The washer isn't reaching or maintaining a high spin speed. This is often due to an unbalanced load triggering a protective low spin, or a problem with the mot…
-
my lg washer won't power on at all, no lights, nothing. i checked the outlet and it's fine.
With a confirmed good outlet, this points to an internal power failure. The most common culprits are a blown thermal fuse (to protect from overheating) or a fa…
-
the wash cycle on my wm4000 takes forever, like 3 hours for a normal load, is that right?
That's likely the washer using its sensor systems. Modern LG washers automatically add time if they sense the load is very dirty, unbalanced, or too sudsy, to …
-
there's a musty smell coming from my lg front load washer, especially the rubber door seal. i run clean cycles.
Mold and mildew are growing in the damp folds of the door gasket and in the detergent dispenser. Clean cycles with hot water help, but they miss the nooks wher…
-
my lg smart washer won't connect to the wifi anymore, the thinq app just says offline.
The connection between your washer and your home wifi router has dropped. This is common after a router reboot, password change, or if the washer's been unplug…
-
getting an le error code on my lg wm4000hwa washer, how do i fix the drain problem?
LE means the washer can't drain the water out within a set time. It's usually a simple clog in the drain system or a kinked drain hose. 1) Unplug the washer. 2…
-
why does my lg front loader make a loud banging noise during the spin cycle? it's the wm4000 model.
That's an out-of-balance load. The washer is trying to spin at high speed, but the clothes are all clumped on one side, making the drum wobble violently agains…
-
my lg wm4000hwa just beeps three times and won't start the cycle, the door is definitely closed.
That's the washer's way of saying it can't lock the door. The three-beep error is almost always a failed door lock mechanism or a problem with the latch. First…
-
mold or mildew smell is coming from the door gasket and detergent drawer
The unpleasant odor in the Samsung WF45R6100AW is caused by the accumulation of "biofilm"—a sticky layer of bacteria, mold, and mildew that feeds on residual f…
-
the washer is shaking violently and banging against the wall on spin
The violent shaking and banging against the wall in the Samsung WF45R6100AW is typically caused by an uncontrolled oscillation of the inner drum. When the drum…
-
it keeps stopping mid-cycle with suds everywhere, error 1E or just stops
The Samsung WF45R6100AW is a High Efficiency (HE) machine designed to use minimal water. When you see the 1E error code or experience mid-cycle shutdowns accom…
-
the door lock just clicks repeatedly and won't latch so i can't start it
The repeated clicking is the sound of the door lock's internal solenoid attempting to engage but failing to do so. This is almost always caused by a failed doo…
-
there's a burning plastic smell and a loud grinding noise during the spin cycle
The combination of a loud grinding noise and a burning plastic smell during the high-speed spin cycle is a classic symptom of a failed spider arm (the three-pr…
-
washer just flashes dC and won't start any cycle, is this a wifi thing?
The "dC" error code on the Samsung WF45R6100AW is a critical communication failure between the Main Power Control Board (PCB) and the Display/User Interface (U…
-
my samsung front loader just keeps beeping and showing 5E, what do i do?
The 5E (or sometimes 5C) error code on the Samsung WF45R6100AW indicates a drain failure. This means the pressure sensor has detected that water is remaining i…
-
the chain brake won't engage when i push the handle forward, it just feels loose.
The brake band is not being pulled tight around the clutch drum. The linkage between the front handle and the brake mechanism is disconnected or broken. Remove…
-
saw vibrates like crazy, way more than it used to. makes my hands numb fast.
Excessive vibration indicates an imbalance in the rotating assembly or loose components. The primary suspect is a damaged or heavily unbalanced chain. First, s…
-
it's throwing oil everywhere but not onto the bar and chain. just spraying out the bottom near the clutch.
Bar oil is being pumped but is not being directed to the bar. The oil outlet hole on the clutch cover or the corresponding channel on the saw body is blocked. …
-
chain gets really loose after just a few cuts, i have to tighten it constantly. tension screw is tight.
The chain is stretching excessively due to incorrect adjustment, a worn bar, or insufficient lubrication. Follow the correct tensioning procedure. Loosen the b…
-
my 120 mark ii is leaking bar oil all over my garage floor even when it's just sitting.
Bar oil is siphoning from the tank through the oil pump. The most common point of failure is the oil tank vent. Locate the oil tank vent. It is a small, often …
-
saw runs okay but the chain won't move, it's just stuck. the bar isn't pinched.
The clutch or the drive sprocket is not engaging. The primary cause is a failed clutch spring or a severely worn sprocket. Remove the side cover and bar. Inspe…
-
chainsaw starts but dies as soon as i give it throttle or take it off choke. runs for like 5 seconds.
The engine is not getting enough fuel under load. The carburetor's idle circuit or main jet is likely clogged from old fuel or the low-speed screw needs adjust…
-
my new husqvarna 120 mark ii won't start at all, not even a sputter. it's full of gas and oil.
The engine is not receiving the correct air/fuel mixture or spark. This is a new-unit setup problem. The most common cause is the master control lever being in…
-
after a cut, my saw smells really hot, like an electrical burning smell, is that normal?
The Milwaukee M18 Fuel 16-inch Chainsaw (2727-20) utilizes a high-torque brushless motor designed to mimic the power of a gas saw. While a faint "warm electron…
-
the oil adjustment screw doesn’t seem to do anything, i turn it but the oil use is the same
The oil adjustment screw on the Milwaukee M18 Fuel 16-inch Chainsaw (2727-20) is often misinterpreted as a flow valve, but it is actually a mechanical stroke l…
-
i put in a fresh battery and pull the trigger but the chain just jerks a little and won’t spin, makes a humming noise
The humming noise you hear is the sound of the brushless motor attempting to rotate while facing an immovable mechanical load, creating a "stalled" state. Beca…
-
the chain won’t oil at all, i see no fling on the bar even with the adjustment screw all the way open
The Milwaukee M18 Fuel 16-inch Chainsaw (2727-20) utilizes a pressure-driven automatic oiling system that is highly sensitive to debris. When you see zero oil …
-
oil is leaking out of my chainsaw all over the place when it’s just sitting in the garage, not even running
The leaking you are experiencing with your Milwaukee M18 Fuel 16-inch Chainsaw (2727-20) is typically caused by the gravity-fed nature of the bar oiling system…
-
my chainsaw runs for a few seconds then just stops, battery is fully charged, what gives?
The Milwaukee M18 Fuel 16-inch Chainsaw (2727-20) utilizes a sophisticated electronic control system designed to prevent the brushless motor from overheating o…
-
the chain on my m18 fuel saw keeps getting loose no matter how much i tighten the bar nuts, it’s driving me nuts
The issue you are experiencing with the Milwaukee M18 Fuel 16-inch Chainsaw (2727-20) is rarely a failure of the bar nuts themselves, but rather a phenomenon k…
-
my milwaukee m18 chainsaw just beeps three times and won’t start at all, what does that mean?
The three-beep sequence on the Milwaukee M18 Fuel 16-inch Chainsaw (2727-20) is a specific diagnostic alert indicating a "Safety Lockout" or "Brake Engagement"…
-
i just got this and the power sharpener attachment doesn't seem to clip onto the bar right, it's wobbly.
The wobbly fit of the PowerSharp attachment on the Oregon CS1500 is typically caused by a misalignment between the sharpener's locking lugs and the specialized…
-
no oil is coming out onto the chain and bar, i've checked the reservoir and it's full.
The Oregon CS1500 utilizes a gravity-fed automatic oiling system that relies on a precise alignment between the internal oil pump and the oil inlet hole on the…
-
the chain keeps coming off the bar or feels super loose right after i tighten it on my cs1500.
The Oregon CS1500 is a consumer-grade saw that utilizes a specific chain-and-bar combination prone to "initial stretch." When a new chain is first put into ser…
-
my chainsaw starts but then the motor sounds like it's bogging down and dying as soon as i try to cut anything.
The "bogging down" effect on the Oregon CS1500 is typically caused by excessive mechanical resistance overcoming the torque of the electric motor. Unlike gas s…