All questions — page 91
Browse by Problem
-
the touch screen on my brita hub is going crazy, registering touches i'm not making or not responding.
The "ghost touching" or unresponsive behavior on the Brita Hub Instant Powerful Countertop Filter touch interface is typically caused by a breakdown in the cap…
-
i set my hub to 190 degrees but the water coming out is barely warm, not hot at all.
The Brita Hub utilizes an internal flash-heating element designed to raise water temperature rapidly as it flows through the heating chamber. When the machine …
-
why is my brita hub making a loud gurgling or humming noise when it's just sitting there idle?
The loud gurgling or humming noise occurring while your Brita Hub is idle is almost always caused by "air lock" or trapped air pockets within the internal pump…
-
the screen on my hub instant just says 'filter' and won't let me do anything else, how do i get past it?
The "Filter" message appearing on your Brita Hub Instant is not a software glitch or a system freeze; it is a hard-lock notification triggered by the internal …
-
my brita hub instant just shows a red light and beeps but won’t start heating, what’s the deal?
The red light accompanied by an audible beep on the Brita Hub Instant is a critical system alert indicating that the heating element cannot engage due to a saf…
-
the wireless hdmi feature (miracast) on my epson 2350 is super laggy and keeps disconnecting.
Wireless projection is highly susceptible to Wi-Fi interference, especially on the crowded 2.4GHz band. The 2350's built-in Miracast/Epson iProjection performa…
-
there's a weird yellow or brownish blob/stain in the corner of the image from my epson 2350, it's not the source.
This is a classic sign of a dust blob on the internal 3LCD panels or the integrator optics. Dust has settled inside the optical block and is being projected, u…
-
my epson 2350 projector keeps randomly turning off by itself after 20 minutes or so.
This is a classic overheating shutdown. The projector's thermal sensors are tripping because the internal temperature is too high, triggering an auto-power-off…
-
the hdmi arc port on my epson 2350 doesn't send sound to my soundbar, it's just silent.
HDMI ARC (Audio Return Channel) on this model is finicky and has specific setup requirements. The most common failure point is the HDMI cable or the Sound Outp…
-
i can't get the keystone correction to work right on my epson 2350, the image is still a trapezoid.
You're likely hitting the physical or digital keystone limit (±30 degrees vertically). The projector is too angled relative to the screen, and software correct…
-
the colors on my 2350 look really washed out and dim, especially reds, it didn't used to be like this.
The projector's lamp is nearing end-of-life or has degraded significantly. This is the #1 cause of faded, dim colors on 3LCD projectors. The color brightness (…
-
my epson home cinema 2350 makes a loud rattling or grinding noise from the fan area, it just started.
Debris (like a small piece of packaging foam or dust clump) has been sucked into the main cooling fan or the fan blades are hitting an internal wire. A failing…
-
my epson 2350 projector is on but the screen is totally black, no image at all. what's going on?
The projector is getting power (lamp lights up) but the 3LCD panels aren't receiving a valid signal or are being blocked. The most common cause is an incorrect…
-
i'm getting a burning electrical smell from my flexispot e7 motor, what should i do?
Stop using the desk immediately. A burning smell indicates an electrical fault, most likely an overheating motor or a short in the wiring. This is a potential …
-
the up and down buttons on the keypad work but the m and number buttons don't do anything
This usually means the keypad is in 'lock' mode, a feature meant to prevent accidental changes to memory presets (great for offices with kids). The basic funct…
-
my desk is wobbly at standing height, especially when i type. did i build it wrong?
Some wobble at full extension is normal, but excessive shaking is usually due to three things: an unlevel floor, an overloaded or unevenly weighted desktop, or…
-
the memory height settings on my e7 just randomly forgot and reset to factory default
The control box has a small internal battery that saves your memory settings when the desk is unplugged. If it loses power completely for an extended time (lik…
-
how do you clean the white laminate top without streaks or damaging it? mine looks awful
Streaks and haze come from using glass cleaner, all-purpose sprays, or anything with wax or silicone. They leave a residue that attracts dust and looks terribl…
-
my desk keeps stopping and beeping three times after moving only a couple inches
The three-beep error is the E7's anti-collision system kicking in. It thinks the desk is hitting an obstruction, even if you don't see anything. The desk needs…
-
i assembled my e7 but it won't turn on at all, no lights on the control panel, nothing
This is almost always a power supply issue. The desk isn't getting electricity to the brain (the control box). Let's trace the power step by step. 1) Check tha…
-
my flexispot e7 desk just started making this loud clicking or grinding noise when it goes up but not down
That loud clicking is almost always the sound of a stripped or damaged plastic gear inside one of the motor's gearboxes. It's a common failure point when the d…
-
the bluetooth connection to the app keeps dropping. i have to re-pair it every time i ride.
The scooter's Bluetooth module has a weak signal or enters a deep sleep that breaks the pairing bond. It's a common glitch. Delete the scooter from your phone'…
-
i updated the firmware and now the acceleration feels super weak, like eco mode all the time.
A firmware update can reset your riding mode or apply regional speed/ power limits. Your scooter is likely in a low-power mode. Check your mode in the app. Ope…
-
the cruise control just turns itself on randomly when i’m riding. how do i stop that?
The Segway Ninebot MAX G2 utilizes a "smart" cruise control algorithm designed to engage automatically after the throttle has been held at a constant position …
-
how do i clean this thing? can i just hose it down? the deck gets really dirty.
You cannot hose it down. Water pressure will force water into the deck through cable grommets and the dashboard seal, causing electrical damage. Use a damp clo…
-
my scooter won’t charge. the charger light stays green when i plug it into the scooter port.
A green light on the charger means it does not detect a battery load. The issue is usually the charging port on the scooter or the internal fuse. First, check …
-
the turn signals on my g2 just stopped working, no lights at all. the buttons in the app do nothing.
The turn signal control module has likely crashed. It's a separate circuit from the main dashboard. A software glitch causes it to freeze. Perform a hard reset…
-
why does my max g2 make a loud clunking or grinding noise from the front wheel when i go over bumps?
That is the front suspension spring binding and then releasing. It's a known issue on early production units. The spring isn't properly seated or lubricated. Y…
-
my ninebot max g2 just shows a red exclamation mark on the dash and won’t move. what’s that mean?
That is a general error code. It means the scooter's controller detected a fault. The most common cause is a brake sensor conflict. Power the scooter off. Pull…
-
why does my nanit keep losing the breathing wear detection? it works for a bit then stops.
The pattern recognition is failing due to low light, pattern obstruction, or the child moving out of the calibrated frame. Follow the calibration checklist. On…
-
the nanit floor stand won't stay tight, the camera slowly droops down overnight.
The friction clutch inside the ball joint of the floor stand has worn out or was not sufficiently tightened from the factory. Locate the black adjustment knob …
-
nanit camera overheats and shuts off, i can feel it's hot to the touch on the back.
The camera is in a confined space or its vents are obstructed, causing thermal shutdown. The back metal plate is the heatsink. Ensure a minimum 6-inch clearanc…
-
i get 'motion detection unavailable' error on my nanit pro all the time, even with perfect wifi.
The camera's onboard processor is overloaded or its firmware is corrupted, disabling the analytics engine. Update the firmware manually. In the Nanit app, go t…
-
nanit app says 'camera offline' but the camera has a solid white light, what does that mean?
The camera is powered and functional, but the connection between the camera and Nanit's cloud servers is broken. A solid white LED confirms local operation. Th…
-
how do you clean the nanit camera lens? it's all smudged and the night vision is super blurry now.
The blurriness you are experiencing during night vision is caused by light diffusion. The Nanit Pro camera utilizes an array of infrared (IR) LEDs surrounding …
-
nanit making a constant high-pitched whining noise, it's really loud and keeps us awake.
This is coil whine from the camera's internal power supply circuitry. It is a known hardware issue with some units. Contact Nanit Support directly through the …
-
my nanit pro camera has a solid red light and won't show up in the app, i've tried restarting everything.
The camera's Wi-Fi connection has failed. A solid red LED indicates it cannot establish or maintain a connection to your network. Perform a full reset cycle. F…
-
the airwrap turns on for a second, makes a click, and shuts off. it won't run at all now.
That click is often the sound of a internal safety switch or relay tripping. Combined with the immediate shutoff, this points to a serious electrical fault, li…
-
i just got my airwrap and the power cord feels weirdly stiff and won't stay coiled, it's always tangled.
That's not a defect, it's a feature. Dyson uses a thick, rubberized cord on the Airwrap that's designed to be heat-resistant and durable. It's notoriously stif…
-
the long barrel attachment for curls gets too hot to touch near the base, is that normal?
Yeah, this one's common. It's normal for the metal barrel near the cuff (where it attaches) to get quite warm during use—that's where the heater is. But it sho…