All questions — page 116
Browse by Problem
-
how do you clean the stupid blade assembly? stuff is caked in the little holes and it smells.
The "caked-on" residue and foul odor are caused by dairy proteins and sugars infiltrating the internal cavity of the blade assembly and the small ventilation h…
-
the machine turns on but the blade just hums and doesn't spin, even on a re-spin. pint is fully frozen solid.
The humming sound without rotation indicates that the motor is receiving power, but the drive shaft is physically stalled. In the NC301, this is almost always …
-
my ninja creami is making a super loud grinding noise like metal on metal, not the normal sound.
The loud, metal-on-metal grinding noise in the Ninja Creami NC301 is almost always caused by a mechanical misalignment between the drive spindle (the rotating …
-
my creami just flashes 'LID' on the screen and won't start spinning, even though the lid is on.
The "LID" error on the Ninja Creami NC301 is a safety interlock failure. The machine is equipped with a magnetic or mechanical microswitch sensor located in th…
-
the touch controls on the panel are unresponsive or beep when i don't touch them
Moisture or cleaning product residue has seeped under the capacitive touch panel, causing a short or phantom touches. This is common if the control panel is wi…
-
after moving, my lg washer shakes violently and walks across the floor on high spin
The shipping bolts were not removed, or the self-adjusting leveling feet are not set. The WT7900HBA has four transit bolts securing the drum for shipment. Turn…
-
door lock light just flashes and it won't start, no error code, just the flashing lock
The washer cannot confirm the lid is securely closed. The lid lock mechanism or its sensor has failed, or the lid is not engaging the strike properly. Ensure t…
-
it leaves a blue or gray sticky lint all over dark clothes, i've cleaned the filter
This is detergent or fabric softener residue, not lint. The WT7900HBA uses an impeller (wash plate) and high-pressure jets. Using too much detergent, or the wr…
-
the smartthinq app won't connect to my washer, it just times out during the wifi setup
The most common cause is the washer's 2.4GHz-only WiFi module conflicting with a dual-band (2.4/5GHz) home network that uses the same SSID name. On your phone,…
-
washer makes a loud grinding or rubbing noise only on the agitate part of the cycle
A foreign object is likely trapped between the stainless steel wash plate (at the bottom of the tub) and the outer plastic basket. Coins, bra wires, and button…
-
getting an le error code on my lg top loader during the spin cycle, clothes are sopping wet
The LE error indicates a motor lock or a failure to sense correct motor speed (RPM) during spin. A drain issue often causes this by leaving the tub too heavy w…
-
my lg wt7900hba says su and just sits there filling with water forever, it never starts washing
The washer is stuck in the "SU" (Standing Water) diagnostic mode. This is a factory test cycle, not a normal wash. It activates when a specific button sequence…
-
it's stuck on sensing and just agitates slowly forever, never moves to fill or wash.
The washer is stuck in the initial "sensing" part of the cycle where it tries to weigh the load. This is usually caused by a failure in the motor control unit …
-
how do i clean the filter on this thing? i'm getting a musty smell and the manual is useless.
The musty smell is mold or mildew growing in residual water trapped in the pump filter housing or the rubber gasket. This model has a clean-out filter for that…
-
the control panel is completely dead, no lights, no response, like it's not getting power at all.
Total loss of power points to the household outlet, the power cord, the door being open, or a blown thermal fuse on the main control board. First, check the ob…
-
my clothes are coming out of the wash still soapy and the rinse cycle doesn't seem to use enough water.
This model uses a HE (High-Efficiency) low-water wash system. The most common cause of soapy residue is simply using too much detergent, or the wrong kind (not…
-
the lid lock light just flashes and it won't start, even though the lid is definitely closed.
The washer's control board isn't getting the "lid is locked" signal from the latch assembly. Either the latch mechanism is faulty, or the wiring to it is damag…
-
washer makes a loud grinding or rumbling noise only during the spin cycle, sounds like it's gonna walk across the floor.
That's classic unbalanced load noise. The WTW5000DW has a built-in vibration sensor, but heavy items like blankets or a single pair of jeans can still get stuc…
-
suddenly getting an F21 error on my whirlpool washer and it won't do anything.
F21 means "Long Drain"—the washer tried to drain but didn't see the water level drop within the expected time. It's a drainage problem, not a fatal error. Firs…
-
my whirlpool top loader just keeps filling with water and then draining it out over and over, it never starts the wash cycle.
This is almost always the washer not sensing the water level correctly. The control board thinks it needs more water, fills, then decides it's too full and dra…
-
it takes forever to fill, like 15 minutes just to get enough water to start washing.
The slow fill time on the GE GTW685BSLWS is almost always caused by a restriction in the water flow, typically occurring at the inlet valve screens. Over time,…
-
the washer is off balance every single load, it thumps and stops during spin.
The thumping and premature stopping during the spin cycle on your GE GTW685BSLWS is typically caused by an "Out of Balance" (OOB) condition. This occurs when t…
-
why does my ge top load washer smell like mildew, i just cleaned it with affresh last week.
DIAGNOSIS> The GE GTW685BSLWS is a high-efficiency (HE) top-load washer designed to use significantly less water than traditional machines. While Affresh table…
-
my washer won't drain at all, it's just full of water and humming.
The humming sound you hear is the drain pump motor energizing, but the impeller is physically unable to rotate. In the GE GTW685BSLWS, this is almost always ca…
-
the lid on my ge gtw685 won't lock, it just clicks and the light flashes, it won't start.
The "clicking" sound combined with a flashing light indicates a Lid Lock Failure. This GE model uses a solenoid-driven locking mechanism that must engage and s…
-
i keep getting an su error code on my ge washer, it fills but then just stops.
The "SU" error code on the GE GTW685BSLWS stands for "Suds" or "Suds Lock." This occurs when the machine's pressure sensor detects an abnormal amount of foam i…
-
why is my gt wash machine making a super loud grinding noise during the spin cycle?
A loud grinding noise during the spin cycle on your GE GTW685BSLWS typically indicates a physical obstruction interfering with the rotating components. The mos…
-
my ge top loader just shows 'PF' on the display and won't do anything, what is that?
The "PF" code on your GE GTW685BSLWS washer stands for "Power Failure." This indicates the machine's electronic control board detected a significant interrupti…
-
clothes are coming out sopping wet after spin, way wetter than they used to
The spin cycle isn't reaching its full speed, so it's not extracting enough water. This is often due to an unbalanced load triggering the machine to limit spin…
-
it won't power on at all, no lights, nothing. checked the outlet and it's fine.
A complete lack of power points to an internal electrical failure, a tripped thermal fuse, or a problem with the lid switch circuit (which controls power). 1) …
-
the washer is walking across the floor and banging loudly on spin
An unbalanced load. The washer's spin cycle is very powerful, and if the weight inside the drum isn't distributed evenly, it will shake violently as it tries t…
-
water won't drain out at the end of the cycle, just sits in the tub
A drainage failure. The pump isn't moving the water out. The most common reasons are a clog in the drain system or a failed pump. First, check for a simple clo…
-
getting a suds error every time i use even a tiny bit of detergent, what gives?
The Maytag MVW7230HW utilizes a sophisticated pressure sensor and water level monitoring system to detect the density of the water. When you see a "Suds" error…
-
it fills with water but then just sits there and doesn't agitate or spin, hums a little
The motor is getting power (hence the hum) but it's not turning the agitator. This usually means the drive belt has slipped off its pulleys or broken entirely.…
-
washer is making a loud grinding noise during the spin cycle, sounds like metal on metal
That's almost certainly a problem with the drive system, and on this model, the most common culprit is a worn-out coupling between the motor and the transmissi…
-
my maytag mvw7230hw just shows F9 E1 and won't start a load, what is that?
That's a lid lock error. The washer's safety system isn't detecting that the lid is properly locked, so it won't let the cycle begin. First, unplug the washer …
-
the 'turbo wash' cycle doesn't seem any faster than the normal cycle, what's the point?
The perception that the TurboWash 360 cycle is not faster than the Normal cycle usually stems from a misunderstanding of how the LG WM4000HWA manages its timin…
-
water is leaking from the bottom front of the machine, not a lot but it's constant during fills.
A constant leak during the fill cycle on an LG WM4000HWA typically indicates a failure in the water delivery system rather than the drainage system. Because th…
-
the washer won't power on at all, no lights, no display, nothing. checked the outlet.
When an LG WM4000HWA exhibits a total blackout—no LED indicators, no display, and no response from the Power button—the issue is typically a break in the elect…
-
there's a musty smell coming from the washer, especially the rubber door seal, even after cleaning.
The musty odor in the LG WM4000HWA is caused by the accumulation of a biological film (biofilm) consisting of undissolved detergent, fabric softener, and skin …