All questions — page 176
Browse by Problem
-
printer says 'out of paper' when the tray is completely full, i've reloaded it five times.
The "out of paper" error on the Epson EcoTank ET-2800 is rarely about the actual quantity of paper and is almost always a failure of the pickup mechanism to su…
-
why does my epson ecotank make a loud grinding noise every time it starts a print or copies something?
The loud grinding or "crunching" noise occurring during the initialization phase of the Epson EcoTank ET-2800 is a mechanical failure known as a carriage jam. …
-
et-2800 is printing super faint or has streaks even though the tanks look full, did i get a dud?
This is almost certainly not a hardware defect or a "dud" unit, but rather a common issue with the ink delivery system in the ET-2800. Because this model uses …
-
my new epson ecotank et-2800 won't connect to wifi, it just keeps searching and never finds my network, what do i do?
The Epson EcoTank ET-2800 often fails to discover networks due to a "frequency mismatch" between the printer's internal wireless card and the router's broadcas…
-
the power light on my pixma mg3620 just blinks and it won't respond to any buttons.
The blinking power light on the Canon PIXMA MG3620 indicates that the printer is trapped in a "Fatal Error" state or is failing its internal POST (Power-On Sel…
-
my computer and phone can't find the canon printer on the network anymore. it was working yesterday.
The Canon PIXMA MG3620 has likely experienced a "DHCP Lease Expiry" or an IP address conflict. Because this model lacks a built-in LCD screen for network confi…
-
the scanner part of my all-in-one won't work. it makes a noise but doesn't move or scan.
The "humming" or grinding noise you hear is the scanner motor attempting to engage the carriage, but the carriage is physically unable to slide across the scan…
-
all my prints from the canon mg3620 have streaks or missing lines of color.
The streaks, horizontal bands, or missing lines of color on your Canon PIXMA MG3620 are caused by partial or complete blockages in the microscopic nozzles of t…
-
i replaced the ink cartridges but my mg3620 still says it's out of ink and won't print.
The Canon PIXMA MG3620 utilizes a "chip-based" ink monitoring system. When you install new PG-245 (Black) or CL-246 (Color) cartridges, the printer reads a sma…
-
my printer is making a loud grinding or crunching noise when it tries to print.
The loud grinding or crunching noise in a Canon PIXMA MG3620 is almost always caused by a mechanical obstruction in the carriage path or a failure in the timin…
-
the wireless setup on my pixma mg3620 keeps failing. it won't connect to my wifi no matter what i try.
The Canon PIXMA MG3620 often suffers from "handshake" failures during wireless setup, where the printer and router fail to exchange security credentials within…
-
my canon mg3620 just shows a solid orange light and won't print or copy anything, what's wrong?
The solid orange Alarm light on the Canon PIXMA MG3620 indicates a general hardware error state that has halted all print and copy operations. Unlike a flashin…
-
printer turns on but the touchscreen is completely blank, no lights, nothing.
The complete absence of a backlight and response on the HP LaserJet Pro MFP M227fdw control panel usually indicates a total loss of power to the User Interface…
-
getting 'error 0xc19a0013' when trying to install the software on windows.
The error code 0xc19a0013 is a specific installation failure that occurs when the HP installer cannot successfully register the driver components within the Wi…
-
scans come out with black streaks or lines down the page every time.
The presence of consistent vertical black lines or streaks on your HP LaserJet Pro MFP M227fdw scans is almost always a result of physical contamination on the…
-
replaced all the toners but it still says 'toner cartridge problem' and won't print.
The "Toner Cartridge Problem" error on the HP LaserJet Pro MFP M227fdw is typically a communication failure between the printer's logic board and the RFID/cont…
-
wireless keeps dropping on my hp m227, have to reboot it to get it back online.
The HP LaserJet Pro MFP M227fdw suffers from a common instability in its network stack, primarily triggered by Dynamic Host Configuration Protocol (DHCP) lease…
-
printer makes a loud grinding noise from the back every time it prints or copies.
The loud grinding or rhythmic "chattering" noise emanating from the rear of the HP LaserJet Pro MFP M227fdw is almost exclusively caused by a failure in the fu…
-
just got a used m227fdw and it says 'supply memory error' on the screen, can't do anything.
The "Supply Memory Error" on the HP LaserJet Pro MFP M227fdw occurs when the printer's logic board cannot successfully communicate with the EEPROM chip embedde…
-
my m227fdw keeps saying 'scanning document jam' but there's no paper stuck anywhere, what do i do?
The "Scanning Document Jam" error on the HP LaserJet Pro MFP M227fdw is a false positive triggered when the Automatic Document Feeder (ADF) sensor fails to det…
-
getting an 'out of memory' error on the screen when trying to print a big pdf or a photo-heavy document.
The "Out of Memory" error on the HP OfficeJet Pro 9015e occurs when the printer's internal RAM buffer is overwhelmed by the size and complexity of the print sp…
-
printer goes to sleep and then won't wake up for a network print job, i have to turn it off and on again every time.
This issue is caused by a failure in the HP OfficeJet Pro 9015e's "Deep Sleep" power state, where the printer's network interface card (NIC) enters a low-power…
-
scanner glass gets dirty constantly and leaves streaks on every scan or copy, how do i clean it properly without damaging it?
The streaks appearing on your HP OfficeJet Pro 9015e scans are typically caused by "debris artifacts." This occurs when a microscopic layer of dust, fingerprin…
-
it makes a loud grinding or crunching noise when it starts up or when printing, sounds like it's coming from the right side.
The loud grinding or crunching noise emanating from the right side of the HP OfficeJet Pro 9015e is typically caused by a mechanical failure in the carriage as…
-
my prints are coming out with streaks or faded lines, especially in colors, even after running the cleaning utility a bunch of times.
The appearance of horizontal streaks or faded bands on an HP OfficeJet Pro 9015e is typically caused by "nozzle dropout." This occurs when microscopic air bubb…
-
the printer screen says 'cartridge problem' or 'cartridge error' for a brand new genuine hp ink cartridge i just put in.
The "Cartridge Problem" or "Cartridge Error" message on the HP OfficeJet Pro 9015e is typically triggered by a communication failure between the printer's prin…
-
just got a 9015e and it won't connect to my wifi during setup, the screen just keeps searching forever.
The HP OfficeJet Pro 9015e often hangs during the initial Wi-Fi handshake because of a "frequency mismatch" between the printer's wireless card and modern Mesh…
-
my hp officejet pro 9015e keeps saying 'paper jam' but there's no paper stuck anywhere, i've checked everything.
The HP OfficeJet Pro 9015e utilizes a series of optical sensors and mechanical "flags" (small plastic levers) to track paper movement. A "ghost jam" occurs whe…
-
my ninja combi makes a loud humming or grinding noise when the fan runs
DIAGNOSIS: That's usually something interfering with the cooling fan, which is located at the back of the unit. A loose piece of food packaging, a stray grain …
-
the touch buttons on my ninja combi are unresponsive or going crazy on their own
DIAGNOSIS: Moisture or steam has likely gotten into the control panel, or there's a sticky residue on the surface confusing the capacitive touch sensors. FIX: …
-
why does my ninja combi beep three times and stop when i try to slow cook?
DIAGNOSIS: The three beeps mean it doesn't detect the inner pot, or it thinks the pot is empty. The slow cook function requires the pot to be in place and has …
-
the keep warm function on my ninja combi turns off by itself after a while
DIAGNOSIS: That's actually by design, not a fault. The 'Keep Warm' function on this model has a maximum automatic runtime for safety and energy reasons. FIX: T…
-
my ninja combi is leaking steam/water from around the lid when pressure cooking
DIAGNOSIS: The sealing ring isn't seated properly, is damaged, or food debris is on the sealing surfaces. A perfect seal is critical for pressure. FIX: 1) Unpl…
-
how do i clean the inside of the lid on my ninja combi? there's gunk in the little hole
DIAGNOSIS: That gunk is built-up grease and food particles. The 'little hole' is the steam release valve vent, and it absolutely needs to be kept clean to func…
-
the air fryer setting on my ninja combi isn't crispy at all, food comes out soggy
DIAGNOSIS: You're probably overcrowding the basket. Air fryers need space for the hot air to circulate. If the basket is packed, you're just steaming the food.…
-
my ninja combi multicooker just beeps and won't start, the display shows 'C01'
DIAGNOSIS: That's the cooker telling you it doesn't think the lid is closed all the way. The C01 code is almost always a lid position or sensor issue. FIX: Thi…
-
the rotisserie spit for my emeril 360 won't turn, the motor just makes a quiet humming sound.
The rotisserie motor is overloaded or jammed. The spit forks are not locked into the rotisserie basket properly, causing misalignment. Remove the basket. Ensur…
-
the non-stick coating on the cooking pot is peeling off, is this safe or do i need a new one?
The non-stick coating on your Emeril Lagasse Power Air Fryer 360 pot has suffered a mechanical failure, likely due to abrasive scrubbing, overheating, or the u…
-
my food is coming out soggy, not crispy, even when i use the air fry setting. what am i doing wrong?
The root cause of soggy food in the Emeril Lagasse Power Air Fryer 360 is almost always "airflow starvation." This machine operates as a convection oven on ste…
-
the display just flashes '0:00' and none of the buttons work, it's completely unresponsive.
The flashing '0:00' on the Emeril Lagasse Power Air Fryer 360 indicates a "logic hang" or a failure in the control board's initialization sequence. This happen…