Washing Machines (Page 3)
-
clothes are coming out soaking wet at the end of the cycle, like the spin didn't work at all
The washer isn't reaching high spin speeds. This is typically caused by an unbalanced load error that cancels the high spin, a faulty motor control m…
-
washer won't power on at all, no lights on the display, checked the outlet and it's fine
Total power loss usually points to a blown thermal fuse (a safety device on the motor), a failed main control board, or a loose internal connection. …
-
the display just says 'i-DOS' and it won't let me select a normal cycle, what does that mean?
Your model has the optional i-DOS automatic detergent dosing system. The display is showing that it's in dosing mode, or it's detected a fault with t…
-
my washer smells musty, especially right when i open the door, even though i run clean cycles
Mold and biofilm in the hidden parts of the machine: the rubber door gasket folds, the detergent dispenser drawer, and the internal sump. Using too m…
-
the door on my bosch front loader won't seal right anymore, there's a gap and it leaks a little water onto the floor
The rubber door gasket (bellows) is probably torn or has a foreign object lodged in it, breaking the seal. On older machines, the gasket just gets br…
-
getting an E16 error code on the display and the machine won't start or stops mid-cycle
E16 means the washer can't drain the water out, or it's draining too slowly. The drain pump is either blocked, the drain hose is kinked/clogged, or t…
-
washer is making a loud grinding or rumbling noise only during the spin cycle, sounds like it's going to walk away
That's almost always an unbalanced load causing the suspension system to work overtime, or something (like a bra wire) has gotten past the drum and i…
-
my bosch 800 series washer just shows a padlock symbol on the display and won't let me open the door or start a cycle
Yeah, this one's common. The child lock is active. It's either been turned on accidentally via the control panel, or the washer still thinks there's …
-
the control knob feels loose and sometimes skips past the cycle i want to select.
The cycle selector knob is not engaging properly with the timer (or electronic control) shaft behind it. The plastic splines inside the knob or on th…
-
it won't drain at all, just sits full of water at the end of a cycle.
The drain pump is either clogged or dead. A small object like a sock, coin, or bra wire can jam the impeller, or the pump motor can burn out from the…
-
the washer shakes violently and walks across the floor during the spin cycle.
The suspension rods are worn out or the shipping bolts weren't removed. This model uses four spring-dampener assemblies (rods) that connect the tub t…
-
water keeps filling into the tub even when the washer is off, it's slowly leaking onto the floor.
The water inlet valve is stuck open. This solenoid-controlled valve lets hot and cold water in. If one of the little solenoids fails or if debris fro…
-
clothes are sopping wet at the end of the cycle, like the spin never happened.
The washer isn't reaching high spin speed, or it's canceling the spin due to an "unbalanced load" error. On these models, a failing lid lock switch c…
-
the washer fills up with water but then just sits there, doesn't agitate at all.
The agitator dogs (also called agitator cams or splutch) are stripped out. These are plastic pieces inside the top of the agitator that engage with t…
-
washer is making a loud grinding noise only on the spin cycle, sounds like metal on metal.
That's the classic sound of a worn-out spider arm. The spider is a three-armed bracket that connects the inner tub to the transmission shaft. On thes…
-
my amana ntw4516fw washer just beeps at me and won't start a cycle, the lid is closed and it's plugged in.
The control board is seeing a "lid lock" error, even though the lid is closed. The microswitch inside the lid lock assembly is either faulty or the a…
-
the wash cycles on my electrolux are taking way longer than the display said they would, like hours longer.
This is normal behavior, not a fault. These washers (and most modern ones) have sensors that constantly check for suds and soil levels. If it detects…
-
water is leaking from the bottom front of my electrolux washer, where's it coming from?
A leak from the front usually points to one of three spots: the rubber door boot gasket is torn, the drain hose connection at the pump is loose, or t…
-
i keep getting suds error on my electrolux, but i'm using he detergent, what am i doing wrong?
The "Suds" or "SD" error means the washer's sensor detected too many suds during a rinse cycle. Even with HE detergent, using too much is the number …
-
my washer just beeps three times and won't start when i press play, what's the deal?
The triple beep is the washer's way of saying "you haven't met all my prerequisites to start." It's not an internal fault code like F01. Run down thi…
-
the door on my electrolux washer won't unlock after the cycle finishes, how do i get my clothes out?
The door lock mechanism (officially called the door strike) has either failed mechanically or isn't getting the signal from the control board to rele…
-
why does my electrolux washer smell like mildew even after i run a clean cycle?
The smell isn't coming from the drum you see, it's from the hidden rubber door boot gasket. Mold and gunk build up in its folds, and a standard clean…
-
my electrolux washer makes a loud grinding or scraping noise only during the spin cycle, is it broken?
Yeah, this one's common. That's almost certainly the spider arm, the part that connects the inner drum to the outer tub's bearing hub, cracking or co…
-
my electrolux front loader is just showing f01 on the screen and won't do anything, what does that mean?
F01 is the communication error code between the main control board and the user interface board. The washer can't start because these two brains aren…
-
washer shakes violently and moves across the floor during spin, it's level.
The suspension system is compromised. Either the shock absorbers have lost their damping fluid or the suspension rods/springs are broken. Tip the mac…
-
the control panel is unresponsive, buttons beep but don't change settings.
The touchpad on the user interface (UI) board has failed or the connection to the main control board is corrupted. This is a known issue with moistur…
-
there's a musty smell coming from inside the drum even after cleaning.
Biofilm and mildew are trapped in the hidden areas of the machine: the rubber bellows (door boot) gasket and the detergent dispenser drawer. Run a cl…
-
the door lock keeps clicking and won't engage, machine won't start.
The door lock assembly (official name is door latch) has failed. The internal solenoid or microswitch is defective, so the control never receives the…
-
clothes are coming out soaking wet, spin cycle doesn't seem to work right.
The washer isn't reaching high-speed spin. This is usually caused by an unbalanced load triggering the out-of-balance protection, or a failed drive m…
-
washer makes a loud grinding or scraping noise only during the spin cycle.
The spider arm, which connects the inner drum to the drive shaft, has corroded and cracked. This is a common failure on this series. The unbalanced d…
-
getting an F21 error code on my whirlpool washer, it just stops mid-cycle.
F21 is a drain error. The pump ran but the control didn't detect a drop in water level within the expected time. The drain hose or pump is restricted…
-
my whirlpool front loader won't power on at all, no lights, nothing. checked the outlet.
The main control board isn't getting power. This is almost always a blown thermal fuse on the main control board or a failed power supply component. …
-
it fills with water super slow, takes forever to start washing.
A slow fill time points to a restriction in the cold or hot water inlet path. The primary suspects are: 1) The inlet screens at the water valve are c…
-
clothes come out of the wash still smelling musty, even right after a cycle.
Persistent musty odor is caused by biofilm and mildew growth inside the machine, typically in three areas: the rubber door boot gasket (not applicabl…
-
the washer won't do anything, no lights, no display, completely dead.
A complete lack of power indicates a failure in the electrical supply or a tripped thermal fuse on the control board. The most common point of failur…
-
water is leaking from the bottom front of the machine onto the floor.
A front-bottom leak has several likely sources. The hierarchy is: 1) Over-sudsing from too much detergent, 2) A loose or damaged inlet hose connectio…
-
the detergent dispenser drawer won't open, feels completely stuck.
The dispenser drawer is likely locked because a cycle is in progress. The GTW840CPNDG has an electronic lock for the drawer during fills and washes t…
-
it keeps stopping and showing 'UE' on the screen, clothes are sopping wet.
Error code UE means 'Unbalanced Load.' The washer's sensors detected an uneven distribution of laundry during the high-speed spin, causing it to abor…
-
washer is making a loud grinding noise during the spin cycle, sounds terrible.
A loud grinding or metal-on-metal noise during high-speed spin points to a failure in the drive system. The most common culprit for this model is the…
-
my ge gtw840cpndg is just blinking 'PF' and won't start a cycle, what is this?
The display is showing error code PF. This indicates a power failure event was detected by the control board. The machine will not operate until the …
-
the touch controls on the panel are unresponsive or beep when i don't touch them
Moisture or cleaning product residue has seeped under the capacitive touch panel, causing a short or phantom touches. This is common if the control p…
-
after moving, my lg washer shakes violently and walks across the floor on high spin
The shipping bolts were not removed, or the self-adjusting leveling feet are not set. The WT7900HBA has four transit bolts securing the drum for ship…
-
door lock light just flashes and it won't start, no error code, just the flashing lock
The washer cannot confirm the lid is securely closed. The lid lock mechanism or its sensor has failed, or the lid is not engaging the strike properly…
-
it leaves a blue or gray sticky lint all over dark clothes, i've cleaned the filter
This is detergent or fabric softener residue, not lint. The WT7900HBA uses an impeller (wash plate) and high-pressure jets. Using too much detergent,…
-
the smartthinq app won't connect to my washer, it just times out during the wifi setup
The most common cause is the washer's 2.4GHz-only WiFi module conflicting with a dual-band (2.4/5GHz) home network that uses the same SSID name. On y…
-
washer makes a loud grinding or rubbing noise only on the agitate part of the cycle
A foreign object is likely trapped between the stainless steel wash plate (at the bottom of the tub) and the outer plastic basket. Coins, bra wires, …
-
getting an le error code on my lg top loader during the spin cycle, clothes are sopping wet
The LE error indicates a motor lock or a failure to sense correct motor speed (RPM) during spin. A drain issue often causes this by leaving the tub t…
-
my lg wt7900hba says su and just sits there filling with water forever, it never starts washing
The washer is stuck in the "SU" (Standing Water) diagnostic mode. This is a factory test cycle, not a normal wash. It activates when a specific butto…
-
it's stuck on sensing and just agitates slowly forever, never moves to fill or wash.
The washer is stuck in the initial "sensing" part of the cycle where it tries to weigh the load. This is usually caused by a failure in the motor con…
-
how do i clean the filter on this thing? i'm getting a musty smell and the manual is useless.
The musty smell is mold or mildew growing in residual water trapped in the pump filter housing or the rubber gasket. This model has a clean-out filte…