Washing Machines (Page 5)
-
how do i clean the filter on my whirlpool washer? it smells musty.
The musty smell comes from mildew growing in hidden, damp places. While there's a cleaning cycle, the main culprit for odor is often the drain pump f…
-
washer won't start, just beeps once when i press power and nothing lights up.
That single beep with no display usually means the control board is getting some power, but the main user interface (the part you press) isn't commun…
-
my top load whirlpool is making a loud grinding noise only on the spin cycle, sounds awful.
A grinding or scraping noise during the spin is almost always something caught between the inner wash basket and the outer tub, or a worn-out drive s…
-
my whirlpool washer just says F21 and won't drain at all, what does that mean?
That's a drain error. Your washer is trying to pump the water out but it's not working, usually because the drain hose or pump is clogged, or the pum…
-
the smart things app won't connect to my washer, it just times out during the wifi setup.
Weak 2.4 GHz WiFi signal at the washer's location. Or a network password/encryption type mismatch. The washer's WiFi module is not powerful. Move you…
-
the washer is walking across the floor during spin, it's really loud and vibrating.
The shipping bolts weren't removed. Or the washer is severely unlevel. The four large bolts in the back secure the drum for transit. Unplug the washe…
-
there's a bad musty smell coming from inside the drum even after i run a clean cycle.
Bio-film and mildew in the hidden spaces. The rubber gasket around the top of the tub, the detergent dispenser, and the sump hose are prime spots. Ru…
-
it keeps stopping mid-cycle and the display says 'nF' or 'no fill'. water trickles in super slow.
nF is a no-fill error. Low water pressure or a clogged inlet valve screen. The washer times out waiting for enough water. Turn off both hot and cold …
-
clothes are sopping wet at the end of the cycle, washer didn't spin them out.
The Samsung WA50R5400AW utilizes a sensitive electronic balance sensor integrated into the tub suspension system. When the washer detects that the lo…
-
the lid won't lock, it just clicks and the cycle won't start. sometimes it says 'dE'.
The "dE" error code on the Samsung WA50R5400AW specifically indicates a "Door Error," meaning the control board is not receiving the required confirm…
-
washer makes a loud grinding noise during the spin cycle, sounds like metal on metal.
The loud, metal-on-metal grinding noise during the high-speed spin cycle on the Samsung WA50R5400AW is typically caused by the failure of the spider …
-
my samsung wa50r5400aw washer just shows '5E' on the display and beeps, then shuts off. what does that mean?
5E is a drain error. The washer can't pump out the water. The drain hose is kinked, clogged, or installed too high. Unplug the washer. Pull it out. C…
-
my washer stopped mid cycle and now the display is blank, no lights, completely dead.
A completely blank display and no power indicates a loss of electrical supply to the control board. The primary suspects are a tripped household circ…
-
the washer is shaking violently and moving across the floor during the spin, even with balanced loads.
Violent shaking and walking indicates the suspension rods or springs are damaged, or the shipping bolts were not removed. On this model, four suspens…
-
how do i run a clean cycle on this ge washer? i don't see a specific button for it.
The GTW465ASNWW does not have a dedicated "Clean Washer" button. The cleaning cycle is initiated through a specific combination of settings. Ensure t…
-
it won't go into spin cycle, just keeps agitating forever and the clothes are sopping wet.
The washer is stuck in a continuous agitation phase and will not advance to spin. This is often caused by a failed lid lock switch or a faulty signal…
-
the washer fills super slow, like it takes 20 minutes just to get enough water to start agitating.
Extremely slow filling points to a restricted water inlet. The most common cause is clogged inlet screens inside the water valve where the hoses conn…
-
water is leaking from the bottom front of my ge gtw465 washer, right under the door area.
A leak from the front-bottom area, near the door, typically comes from the drain pump or its connecting hoses. The pump housing or its seal can crack…
-
washer is making a loud grinding noise only on the agitate part of the cycle, spin is fine.
A loud grinding noise during agitation, with normal spin, indicates a problem with the agitator dogs or the agitator itself. On this model, worn plas…
-
my ge top load washer gtw465asnww just keeps saying 'unb' and won't start a cycle, what does that mean?
The display is showing "unb". This is the "unbalanced load" error code for your GTW465ASNWW. The washer detected an uneven distribution of laundry du…
-
it won't finish a cycle, just stops partway through and sits there with the timer stuck. no error codes.
The washer is likely stuck waiting for a condition to be met, most commonly because it's not filling or draining properly, or a temperature sensor is…
-
the washer shakes and walks violently across the floor during the spin, it's really loud.
The load is severely out of balance, or the suspension rods/springs that stabilize the tub have worn out or failed. An unbalanced load is the first t…
-
all the lights on the control panel are flashing and it's completely unresponsive, won't do anything.
The main control board has likely locked up or detected a fault. It's essentially having a full-system panic attack. Perform a hard reset. Unplug the…
-
my washer won't drain at all, just sits there with water in the bottom at the end of the cycle.
The drain pump is either clogged or has failed. A clog is way more likely—something like a small sock, hair, or a coin has jammed the impeller. Unplu…
-
how do i clean the filter on my speed queen top loader? i can't find it anywhere.
You're looking for a pump filter, but the TR7003WN doesn't have a user-serviceable lint filter or pump clean-out like some front-loaders. The main fi…
-
it fills with water super slow, takes forever to start washing. water pressure everywhere else is fine.
The inlet water valves on the back of the washer are probably clogged with sediment or mineral scale. Yeah, this one's common, especially if you have…
-
the washer is making a loud grinding noise only during the spin cycle, sounds like metal on metal.
That's almost certainly the spider arm—the big three-armed bracket that holds the inner tub to the drive shaft. On some older TR7003WN units, it can …
-
my speed queen tr7003wn washer just keeps beeping non-stop and won't start a cycle, what's wrong?
The washer is stuck in a beeping alarm state, usually because the lid isn't closed and latched properly. The lid switch on these is pretty particular…
-
it's not filling with enough water, even on the deep water wash setting, clothes are dry on top.
The most likely cause is a clogged or slow-filling water inlet valve screen, restricting flow. Turn off both hot and cold water supply valves behind …
-
the clean washer light is flashing and i can't get it to turn off, how do i reset it?
The washer's reminder system is alerting you that it's time to run a cleaning cycle. It's a timer-based reminder, not a sensor. Run a Clean Washer cy…
-
it's vibrating and walking across the floor violently on high spin, really loud.
The washer is out of level, or the shipping bolts (or one of them) were not fully removed during installation. First, confirm all four shipping bolts…
-
the lid lock light just keeps blinking and it won't start or let me open it.
The washer isn't registering that the lid is fully closed and latched, so it won't engage the lock or start. Ensure nothing (like a sock or label) is…
-
it's leaving dark gray or black greasy streaks on my clothes, only on certain loads.
The appearance of dark gray or black greasy streaks on your Maytag MVW7230HW is typically caused by a failure of the tub seal or a leak in the transm…
-
clothes are still soaking wet at the end of the cycle on my lg front loader, not spun dry.
The washer isn't reaching or maintaining a high spin speed. This is often due to an unbalanced load triggering a protective low spin, or a problem wi…
-
my lg washer won't power on at all, no lights, nothing. i checked the outlet and it's fine.
With a confirmed good outlet, this points to an internal power failure. The most common culprits are a blown thermal fuse (to protect from overheatin…
-
the wash cycle on my wm4000 takes forever, like 3 hours for a normal load, is that right?
That's likely the washer using its sensor systems. Modern LG washers automatically add time if they sense the load is very dirty, unbalanced, or too …
-
there's a musty smell coming from my lg front load washer, especially the rubber door seal. i run clean cycles.
Mold and mildew are growing in the damp folds of the door gasket and in the detergent dispenser. Clean cycles with hot water help, but they miss the …
-
my lg smart washer won't connect to the wifi anymore, the thinq app just says offline.
The connection between your washer and your home wifi router has dropped. This is common after a router reboot, password change, or if the washer's b…
-
getting an le error code on my lg wm4000hwa washer, how do i fix the drain problem?
LE means the washer can't drain the water out within a set time. It's usually a simple clog in the drain system or a kinked drain hose. 1) Unplug the…
-
why does my lg front loader make a loud banging noise during the spin cycle? it's the wm4000 model.
That's an out-of-balance load. The washer is trying to spin at high speed, but the clothes are all clumped on one side, making the drum wobble violen…
-
my lg wm4000hwa just beeps three times and won't start the cycle, the door is definitely closed.
That's the washer's way of saying it can't lock the door. The three-beep error is almost always a failed door lock mechanism or a problem with the la…
-
mold or mildew smell is coming from the door gasket and detergent drawer
The unpleasant odor in the Samsung WF45R6100AW is caused by the accumulation of "biofilm"—a sticky layer of bacteria, mold, and mildew that feeds on …
-
the washer is shaking violently and banging against the wall on spin
The violent shaking and banging against the wall in the Samsung WF45R6100AW is typically caused by an uncontrolled oscillation of the inner drum. Whe…
-
it keeps stopping mid-cycle with suds everywhere, error 1E or just stops
The Samsung WF45R6100AW is a High Efficiency (HE) machine designed to use minimal water. When you see the 1E error code or experience mid-cycle shutd…
-
the door lock just clicks repeatedly and won't latch so i can't start it
The repeated clicking is the sound of the door lock's internal solenoid attempting to engage but failing to do so. This is almost always caused by a …
-
there's a burning plastic smell and a loud grinding noise during the spin cycle
The combination of a loud grinding noise and a burning plastic smell during the high-speed spin cycle is a classic symptom of a failed spider arm (th…
-
washer just flashes dC and won't start any cycle, is this a wifi thing?
The "dC" error code on the Samsung WF45R6100AW is a critical communication failure between the Main Power Control Board (PCB) and the Display/User In…
-
my samsung front loader just keeps beeping and showing 5E, what do i do?
The 5E (or sometimes 5C) error code on the Samsung WF45R6100AW indicates a drain failure. This means the pressure sensor has detected that water is r…
-
how do you deep clean the inside of an auertech portable washer? it's starting to smell
The musty smell in your Auertech portable washer is caused by a buildup of detergent residue, fabric softener, minerals from hard water, and mold or …
-
my auertech portable washer is leaking from the bottom, anyone else have this?
DIAGNOSISA leak from the bottom of your Auertech portable washer typically means water is escaping from a connection point or component underneath th…