Water Filters & Purifiers (Page 3)
-
express water ro5dx making water slow, like a trickle, took forever to fill a glass. help?
This "trickle" effect in the Express Water RO5DX is typically caused by a failure in the pressure differential between the source water and the stora…
-
just got an express water ro5dx, is the water safe to drink if it tastes kinda salty?
This salty or "brackish" taste in a brand new Express Water RO5DX system is typically caused by one of two things: the presence of factory preservati…
-
express water ro5dx installed but my kettle is getting white crusty stuff inside crazy fast, is it broken?
The white, crusty buildup you are seeing in your kettle is calcium carbonate scale, a direct result of "hard water." This occurs when minerals like c…
-
my express water ro5dx is making water taste kinda flat and boring, is this normal?
The "flat" or "boring" taste you are experiencing with your Express Water RO5DX is a result of extreme purity, specifically a phenomenon known as "ag…
-
will the cuzn uc-200 filter make my water softer or reduce TDS?
The CuZn UC-200 Under Sink Water Filter is a contaminant-reduction system, not a water softening or desalination system. There is a critical technica…
-
i installed my cuzn uc-200 but no water comes out at all, cold water valve is on. what did i do wrong?
This issue is almost always caused by a "cross-connection" or an airlock resulting from incorrect hose routing. In the CuZn UC-200 system, water must…
-
my cuzn water filter is making a gurgling noise, is something wrong?
The gurgling sound in your CuZn UC-200 Under Sink Water Filter is almost always caused by "air pockets" or "slugs" of air trapped within the filter c…
-
how do i know when to replace the filter in my cuzn uc-200?
The CuZn UC-200 is a non-electric, passive filtration system, meaning it lacks a built-in digital timer, pressure sensor, or LED indicator to signal …
-
can i use my cuzn uc-200 with my private well water?
The CuZn UC-200 is a high-capacity carbon block filter designed specifically for "polishing" municipal water—removing chlorine, chloramines, and vola…
-
i think my cuzn filter is leaking from one of the connections, what should i do?
The CuZn UC-200 is a high-flow under-sink system, and leaks typically occur at the connection points due to one of three reasons: improper seating of…
-
my cuzn uc-200 water flow is super slow, barely a trickle. help?
The sudden drop in water pressure or "trickle" effect in a CuZn UC-200 system is typically caused by a saturation of the carbon block media or a phys…
-
just installed my cuzn uc-200 under sink filter and the water coming out is dark brown, is this normal?
The dark brown water is almost certainly caused by loose carbon dust (or "fines") from the brand new filter cartridge. This is a common occurrence wi…
-
the water volume on my bluevua isn't accurate, i set it for 1 liter but it makes way less
The Bluevua RO100ROPOT utilizes a flow-metering system that calculates water volume based on the speed and duration of water passing through the RO m…
-
going on vacation for two weeks, can I just leave my bluevua water filter system plugged in?
Leaving the Bluevua RO100ROPOT plugged in and idle for two weeks creates a high risk of "stagnation biofilm" and microbial proliferation. Because thi…
-
my bluevua ropot's tds reading on the screen is high, like 100+ on the OUT side, isn't it supposed to be lower?
The presence of a high TDS (Total Dissolved Solids) reading on the "OUT" side of your Bluevua RO100ROPOT—specifically readings exceeding 100 ppm when…
-
bluevua countertop ro system leaking water from the bottom, just noticed a puddle
Water leaking from the bottom of the Bluevua RO100ROPOT is almost always caused by a failure in the primary seal interface between the filter cartrid…
-
why is my bluevua ropot water filter so slow? takes forever to fill the carafe
The slow flow rate in the Bluevua RO100ROPOT is typically caused by a restriction in the membrane's permeate flow or a buildup of mineral deposits wi…
-
just replaced the filters on my bluevua ro100ropot and now it won't start at all, the button does nothing
The Bluevua RO100ROPOT is designed with a safety interlock system tied to its filter lifespan monitors. When you replace the filters, the internal lo…
-
bluevua ropot making a loud buzzing noise from the pump, is it broken?
The loud buzzing or vibrating noise emanating from the Bluevua RO100ROPOT pump is typically caused by "air lock" or cavitation. This occurs when air …
-
my bluevua ropot water filter keeps stopping halfway through, the tank still has water but it just shuts off, what gives?
The Bluevua RO100ROPOT is experiencing a "Concentrate Lockout" trigger. This system utilizes a precision weight-sensing mechanism at the base of the …
-
how often do i really need to change the brita longlast+ filter? the manual says 6 months but my water still tastes fine.
The Brita Longlast+ filter uses a high-capacity ion-exchange resin and a dense activated carbon block designed to last significantly longer than stan…
-
my brita filter is leaking water around the edges where it sits in the reservoir, why?
The leak occurring around the edges of the Brita Longlast+ filter is typically caused by a failure in the compression seal between the filter cartrid…
-
the lid on my brita water pitcher won't close all the way or feels loose, how do i fix it?
The issue with the Brita Longlast+ lid not seating properly or feeling loose typically stems from a misalignment of the hinge pivot points or a displ…
-
how do i reset the filter light on my brita pitcher after i change it?
The Brita Longlast+ Water Filter Pitcher utilizes a digital indicator light to track the lifespan of the filter based on a preset timer rather than a…
-
my brita longlast+ pitcher indicator light isn't blinking at all anymore, is it broken?
The Brita Longlast+ indicator light operates on a timed countdown mechanism rather than a sensor that detects water purity or filter saturation. When…
-
my brita pitcher filter light is blinking red and won't stop, what do i do?
The blinking red light on your Brita Longlast+ Water Filter Pitcher is a visual alert triggered by the internal electronic timer, not a physical sens…
-
the blue bypass valve on the side is stuck, i can't turn it to bypass mode.
The blue bypass valve on the Aquasana AQ-5200 is a quarter-turn ball valve designed to redirect water flow around the filter canisters during mainten…
-
water is leaking from the top of the filter housing where it screws into the black head.
The leak at the junction of the Aquasana AQ-5200 filter housing and the black head assembly is almost always caused by a failure in the primary seal,…
-
the smart monitor voice is talking but i can't understand it, sounds garbled and the light is solid red.
The Aquasana AQ-5200 Smart Monitor is an electronic tracking device that monitors water flow through a turbine to calculate filter life. When the voi…
-
the filtered water tastes weird, kinda plastic or chemical, even after running it for a week.
The "plastic" or "chemical" taste in a new Aquasana AQ-5200 installation is typically caused by one of two things: carbon fines or volatile organic c…
-
my filter is making a loud gurgling or humming noise inside the cabinet every time i use the water.
The gurgling noise in the Aquasana AQ-5200 is caused by "air pockets" trapped within the filter canisters or the internal tubing. This typically happ…
-
the blue light on my aquasana is blinking fast and the voice says "filter change" but i just changed them a month ago.
The Aquasana AQ-5200 utilizes an electronic monitoring system that operates primarily on a volumetric timer rather than a real-time chemical sensor. …
-
installed my aq-5200 and now the water pressure at my kitchen faucet is terrible, just a weak trickle.
Low water pressure in the Aquasana AQ-5200 is typically caused by one of two issues: an air lock within the filter housings or a "dry start" where th…
-
my aquasana under sink filter is dripping water from the housing, not the connections, just a slow drip from the plastic itself.
The slow drip emanating directly from the plastic body of the Aquasana AQ-5200 housing is almost always indicative of a stress fracture or a hairline…
-
the plastic on my brita pitcher has gotten cloudy and scratched up, can i clean it or is it ruined?
The cloudiness and scratching on your Brita Stream Rapids pitcher are caused by a combination of mineral buildup (limescale) and mechanical abrasion.…
-
water is pooling in the top reservoir of my brita and not draining down through the filter at all.
This issue is almost always caused by an "air lock" or a vacuum seal forming between the filter cartridge and the reservoir base. Because the Brita S…
-
the lid on my stream rapids won't lock onto the pitcher right, it feels loose and wobbly even when it clicks.
The instability in the Brita Stream Rapids lid is typically caused by a misalignment of the locking tabs or a failure in the tension spring mechanism…
-
the little electronic filter indicator on my brita won't reset, i held the button but it just stays red.
The Brita Stream Rapids indicator is a capacitive-touch timer system designed to track the approximate lifespan of the filter based on time and usage…
-
the water from my stream rapids tastes kinda plasticky or weird, even after changing the filter. what's going on?
The "plasticky" or chemical taste in a Brita Stream Rapids pitcher typically stems from one of two root causes: residual manufacturing lubricants or …
-
my brita stream rapids pitcher is leaking water from the bottom seam where the lid clicks on, it just drips down the side when i tilt it.
The leaking issue in the Brita Stream Rapids pitcher typically stems from a failure in the vacuum seal between the reservoir body and the lid assembl…
-
my tds meter shows 000 but the water still tastes bad or flat. is the meter lying?
The TDS (Total Dissolved Solids) meter is not lying, but it is providing a very narrow window into your water quality. The meter measures electrical …
-
i cleaned my pitcher with vinegar and now the water tastes sour. how do i get the taste out?
The sour taste is caused by acetic acid residue from the vinegar penetrating the porous surface of the BPA-free plastic used in the ZeroWater 10-Cup …
-
the lid on my zerowater pitcher won't stay closed, it just pops open when i try to pour.
The failure of the ZeroWater 10-Cup pitcher lid to stay closed is typically caused by a mechanical failure of the tension tabs or a misalignment of t…
-
white flakes or black specks are coming out of my zerowater filter into the pitcher.
The presence of particulates in your ZeroWater pitcher is a sign of "media migration," where the internal filtration materials are escaping the cartr…
-
the water is taking forever to filter through, just a slow drip. it used to be faster.
The slow drip is caused by the accumulation of dissolved solids, sediment, and mineral scale within the filter's ion-exchange resin and physical filt…
-
my zerowater tds meter reads 006 or higher right after i put in a new filter. isn't it supposed to be zero?
The presence of a reading such as 006 or higher immediately following a filter change is typically caused by "channeling" or insufficient saturation …
-
water is leaking from the bottom of my zerowater pitcher, around where the reservoir sits. it's not overfilled.
The leak occurring at the junction where the filter reservoir meets the main pitcher body is almost always caused by a failure in the airtight seal b…
-
my new zerowater pitcher tastes weird or plastic-y, even after rinsing. what did i do wrong?
The "plastic" or chemical taste in a new ZeroWater 10-Cup Pitcher usually stems from two distinct sources: residual manufacturing lubricants on the p…
-
my berkey lower chamber is getting a pink or slimy film on the inside walls, what is this and how do i clean and prevent it?
The pink or slimy film appearing on the interior walls of your Berkey Royal lower chamber is almost certainly a colony of Serratia marcescens. This i…
-
the water level in my berkey upper chamber isn't going down even after a day, seems completely clogged, what do i do?
The primary cause of a complete flow stoppage in the Berkey Royal system is a phenomenon known as an "airlock." This occurs when air bubbles become t…