All questions — page 197
Browse by Problem
-
how do i clean the filter on my honeywell hpa300? do i just vacuum it?
The Honeywell HPA300 utilizes a dual-stage filtration system consisting of a coarse pre-filter (the mesh layer) and a True HEPA filter (the thick, pleated whit…
-
how do i prioritize a specific room with the honeywell t9 and the wireless sensors?
The Honeywell Home T9 (RCHT9610WFSW2003) operates using a "Weighted Average" logic. By default, the system attempts to balance the temperature across all paire…
-
is the honeywell t9 compatible with my heat pump? i'm getting weird heating and cooling at the same time
The Honeywell Home T9 (RCHT9610WFSW2003) is fully compatible with heat pump systems, but the "simultaneous heating and cooling" phenomenon is almost always cau…
-
honeywell t9 thermostat display is on but it won't change the temperature when i press the arrows
The Honeywell Home T9 (RCHT9610WFSW2003) utilizes a software-level safety lock called "Temperature Setpoint Limits." When the display remains active and respon…
-
my honeywell t9 says it's heating but my furnace isn't kicking on, help?
This issue occurs when the Honeywell T9 (RCHT9610WFSW2003) registers a "Call for Heat" on the display, but the physical furnace ignition sequence never begins.…
-
my ego mower's blade stopped spinning but the motor still runs, what gives
The blade adapter or drive key has sheared. This is a safety feature to prevent motor damage. Disconnect the battery. Tilt the mower. Attempt to turn the blade…
-
the grass catcher on my lm2135sp won't stay on, keeps falling off
The bag frame, mulch plug, or side discharge chute is not installed correctly, or the bag frame is damaged. Follow this checklist: Confirm the mulch plug (part…
-
ego power+ mower handle feels loose and wobbly, how do i tighten it
Loose hexagon socket screws on the handle assembly and beam assemblies are the fix. You need a hex key. Check these points: Tighten the 4 hexagon socket screws…
-
how do i change the cutting height on the ego lm2135sp, the lever is stuck
The height adjusting lever is likely jammed with grass clippings or debris. You'll need to free it up. First, make sure the mower is off and the battery is rem…
-
my ego 56v mower is making a loud clicking or grinding noise from under the deck
Yeah, this one's common. It's almost always a foreign object caught in the blade or a damaged blade hub. First, safety: Disconnect the battery. Tilt the mower …
-
self-propel on my ego lm2135sp is weak or intermittent, feels like it's dragging
The self-propelled unit's motor and gear assembly or drive belt is the likely cause. Diagnose in this order: Check the wheel assemblies (part number 10, 37). E…
-
ego power+ lm2135sp won't start at all, nothing happens when i pull the lever, help
The switch assembly or the internal wire assembly has a bad connection. First, check the battery. Ensure it's fully seated in the battery cover assembly and ch…
-
where is the serial number on a greenworks 40v 21 inch mower? need it for warranty.
You need the serial number to register your Greenworks mower for warranty coverage or to request service. This number is specific to your unit and is found on …
-
my greenworks cordless mower just stopped in the middle of mowing and won't restart, battery light is still on.
Likely an overload or thermal protection trigger. The motor shut down to protect itself. Remove the battery to fully reset the mower's system. Check for a clog…
-
the blade on my greenworks mower seems wobbly or loose, is that normal?
A wobbly or loose blade on your Greenworks 40V mower is not normal and is a serious safety hazard. This condition almost always indicates that the central blad…
-
greenworks 40v battery won't click into my lawn mower, feels loose.
This issue is typically caused by one of three things: debris accumulation in the battery bay, a fatigued or displaced locking tab on the battery casing, or a …
-
how do i clean under my greenworks cordless mower deck? it's caked with grass.
You'll want to clean that out to keep your cut even and prevent corrosion. Here's the safe way to do it. First, turn the mower off and pull out the battery pac…
-
greenworks 40v mower is making a horrible grinding noise when i try to mow, sounds like metal on metal.
Yeah, this one's common. You've almost certainly got a rock, stick, or a wad of packed grass jammed under the deck, hitting the blade. Stop immediately. Turn t…
-
my greenworks 40v lawn mower won't start when i pull the handle, battery is charged, what gives?
The primary cause of a Greenworks 40V 21-Inch mower failing to start despite a charged battery is a failure in the safety interlock circuit. This mower utilize…
-
can i use my ego lm2135sp without the grass catcher, just side discharge?
The EGO LM2135SP is designed for flexible operation, and you can absolutely use it without the grass catcher. The mower supports mulching, bagging, and side di…
-
my ego lawn mower is leaving uneven strips of uncut grass, what should i check?
The appearance of uneven strips or "mohawks" of uncut grass on an EGO LM2135SP is typically caused by one of three things: an improper cutting height setting, …
-
ego mower won't go into self-propelled mode, the button does nothing. fix?
DIAGNOSISThe self-propelled function on your EGO LM2135SP mower typically fails for a few specific mechanical or electrical reasons. The most common culprit is…
-
how do you change the blade on an ego lm2135sp? i can't figure out how to lock it.
The difficulty in locking the blade on the EGO LM2135SP stems from the high-torque design of the motor hub. Because this is a brushless DC motor, there is very…
-
ego self-propelled mower making a loud grinding noise when i engage the drive, what's broken?
DIAGNOSISA loud grinding noise when engaging the self-propel drive on your EGO LM2135SP indicates mechanical failure within the drive transmission. The sound i…
-
my ego power+ lm2135sp mower won't start at all, no lights or anything, anyone know why?
Your EGO LM2135SP mower showing no power or lights indicates a complete interruption in the main electrical circuit. The three most likely culprits are a batte…
-
the red fault light on my honda eu2200i is flashing once every two seconds. what does that mean?
The FAULT/CO SENSOR LIFE indicator is flashing a specific pattern. A flash once every two seconds indicates the CO-MINDER carbon monoxide sensor is near the en…
-
just got a makita xsh03z, can i use it to make plunge cuts or not?
The Makita XSH03Z is a cordless circular saw designed primarily for rip and cross-cuts, meaning its lower blade guard is spring-loaded to snap shut the moment …
-
makita circular saw battery gets really hot when i'm using it, is that normal or a problem?
While all lithium-ion batteries generate some heat during discharge, the Makita 18V LXT XSH03Z is a high-draw tool that can push batteries to their thermal lim…
-
my honda eu2200i ran out of gas. i refilled it but now it takes like 10 pulls to start. is it broken?
Nah, it's not broken. This is a known quirk with the vacuum-operated fuel pump. When the carburetor is completely dry, it takes extra pulls to prime the system…
-
my makita saw blade is wobbling and the cut is all over the place. did i install it wrong?
A wobbling blade on the Makita XSH03Z is almost always caused by a failure in the "sandwich" of components between the arbor nut and the blade body. The most c…
-
what's the little lever on the gas cap of my honda generator for? i can't remember if it should be on or off.
That small plastic lever located on the top of the Honda EU2200i fuel cap is the fuel tank vent valve. Its primary purpose is to manage the atmospheric pressur…
-
can i use my makita cordless circular saw to cut wet or pressure treated wood?
The Makita XSH03Z is engineered for dry, dimensional lumber, but it can handle wet or pressure-treated (PT) wood if you understand the mechanical stressors inv…
-
honda eu2200i making a weird clicking noise from the control panel, and the eco throttle light is acting funny. is this normal?
The clicking noise is likely the AC circuit protectors (the red buttons) tripping due to an overload. The Eco Throttle system behavior changes under load, whic…
-
can i connect my honda eu2200i to another generator to get more power? i have an old champion.
No, you cannot connect your Honda EU2200i to your old Champion generator to get more power. Connecting to an incompatible generator can cause serious damage. T…
-
what's the right way to set the depth on a makita 18v lxt saw? i keep getting crappy cuts.
Poor cut quality on the Makita XSH03Z is almost always a result of "over-extension" or "under-extension" of the blade. When the blade is set too deep, the saw …
-
my honda eu2200i generator just shut off by itself and a red light is flashing. what does this mean?
The CO-MINDER system detected a potentially dangerous level of carbon monoxide and shut the engine down for safety. The flashing light is the CO ALARM indicato…
-
the lower guard on my makita circular saw is sticking and not closing fast. is this safe to use?
The lower guard on the Makita XSH03Z is designed as a spring-loaded safety mechanism that must snap shut the instant the blade leaves the material. When the gu…
-
just got a honda eu2200i and it won't start, the pull cord feels fine but nothing. what's wrong?
The engine was shipped without oil. It has an Oil Alert system that prevents startup if the oil level is too low. FIX: Place the generator on a level surface. …
-
makita xsh03z saw keeps kicking back on me, almost lost control. how do i stop this?
Kickback on the Makita XSH03Z occurs when the rotating blade becomes pinched or bound by the workpiece, causing the motor's torque to violently propel the saw …
-
my makita 18v lxt circular saw won't turn on at all, battery is charged. what's wrong?
The Makita XSH03Z is a brushless model, meaning it relies on a complex electronic controller to bridge the gap between the battery and the motor. When the tool…